Product Search
ACCESSORIES
NOTE:
All of Midnite Solar's listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
MNCCB-ROSIE-R
Classic charge controller right mounting bracket.
Price: $45.00
MNCCB-ROSIE-L
Classic charge controller left mounting bracket.
Price: $45.00
9-497-1
RJ45 connector for Midnite cat5
An 8-pin/8-position connector for Cat5 cable.
Price: $3.00
MNZWIRE240-5PK
240V BY-PASS WIRE - Bag of 5
Price: $5.00
MNZWIRE120-5PK
120V BY-PASS WIRE - Bag of 5
Price: $5.00
MNCAT5-600
(Previous Model Num: MNCAT5-600 - Cat5 Cable)
MNCAT5-600 USE-2 600 volt rated cable.
Shielded
Double insulated
UV resistant
Direct burial
Price: $2.25 per ft.
MNCCB-SW
Charge controller bracket for mounting ANY Classic to the left side of the Scheider SW E-Panel
Price: $86.00
MNCAT5-600-FULLROLL
Cat 5 cable sold in complete rolls of 1600 feet.
MNCAT5-600 USE-2 600 volt rated cable
Shielded
Double insulated
UV resistant
Direct burial
Price: $2285.00
MNEDC-BLANK-5PK
Old Model # MNEDC-BLANK
5 pack of blanks
3/4 inch wide panel mount breaker whole plug
Designed to plug unused MNEDC breaker Knock Outs
Sold in packs of 5 with screws included

Price: $31.00
MNMATE3BRKT
Mate 3 Mounting bracket
Mounting bracket for the Mate 3, allows mounting of the Mate 3 on any of our MidNite E-Panels that support the Outback Inverters.
Price: $54.00
MN3-015-1
(Previous Model Num: Tin Plated Copper Plate)
063" x 2.1" x 1.5" One 3/8", five .250, two .203" holes. Used on MNDC shunts for an additional bat minus battery connections.
Price: $26.25
MNCCCK
One inch close nipple, three one inch lock nuts and two insulating bushings. Use for connecting charge controllers through the side to MidNite E-Panels or other similar enclosures.
Price: $15.00
MNSHUNT
(Previous Model Num: Shunt)
50mV/500amp includes taptite mounting screws. Has two 8-32 tapped holes on one end to attach a bus bar. This is the industry standard shunt.
Price: $50.00
MNSHUNT-1000/50
This is the 1000 amp 50 miV shunt.
Price: $115.00
MNSHUNT-1000/100
This is the 1000 amp 100 miV shunt
Price: $130.00
MNPV3DF
Replacement dead front for the MNPV3 and MNPV2-MC4.
Price: $23.00
MNSR-1000-25PK
OLD MODEL # MNSR-1000
This 1/2 in 1000V Heyco Strain Relief accepts two 6mm PV wires.
Sold in bags of 25. Nut is included.
Price: $74.50
MNHOLE PLUG 1/2-25PK
OLD MODEL # MNHOLE PLUG 1/2
For use anywhere you need a water tight hole plug to fill a 1/2 knock out. This is the same hole plug we use on our Nema 4X combiner boxes.

Sold in bags of 25.
Price: $90.00
MNPV6DF
Replacement dead front for the MNPV6, MNPV6 Disco and MNPV4-MC4.
Price: $31.00
MNPV12DF
Replacement dead front for the MNPV12 and MNPV8-MC4.
Price: $48.00
MNWRENCH
(Previous Model Num: MN-Wrench)
A 1/2 and 3/4 inch wrench used on MidNite's E-Panels where 1/2 inch strain reliefs and MNADAPTER 1/2-3/4 adapters are used. Great tool to get into tight places.
Price: $6.00
MNPV3FA
Replacement fuse adapter for the MNPV3 and MNPV2-MC4 combiners.
Price: $15.00
MNPV6FA
Replacement fuse adapter used with either MNPV6 or MNPV4-MC4.
Price: $16.00
MNPV6-DISCO-SLIDER
Replacement Slider for the MNPV6 Disco, MNPV6-250 DISCO and MNPV6-DISCO AC MICRO.
Price: $12.00
MNPV12FA
Replacement fuse adapter to be used with the MNPV12 or MNPV8-MC4. The deadfront for this fuse adapter requires two adapters.
Price: $16.00
MN-SHORT-DINRAIL
The same Din Rail mount that is used in the 120 vac E-Panels, includes mounting hardware. Holds 5 poles of din rail breakers.
Price: $40.00
MN-TALL-DINRAIL
The same Din Rail mount that is used in the 240 vac E-Panels, includes mounting hardware.Holds up to 6 poles of din rail breakers.
Price: $41.00
MNNOTTAGUTTER-DR
(Previous Model Num: MN-Nottagutter-Dinrail)
Din rail to fit the Nottagutter, includes mounting hardware.
Price: $40.00
MNResistor600W-2.0
(Previous Model Num: MNResistor600W 2.0 Ohm)
This resistor is made of a ceramic tube with flat, waved alloy resistance wirewound on it.
Price: $135.00
MNRESISTOR600W-0.8
(Previous Model Num: MNRESISTOR600W 0.8 Ohm)
This resistor is made of a ceramic tube with flat, waved alloy resistance wirewound on it.
Price: $135.00
MNRESISTOR1500W-3.0
(Previous Model Num: MNResistor1500W 3.0 Ohm)
This resistor is made of a ceramic tube with flat, waved alloy resistance wire-wound on it.

Resistor 3 Ohm 1500 watt 1500W/3R
Price: $180.00
MNBACKPLATE
Discontinued once stock depleted
16 gauge gray steel accepts one or two EPanels, (wide or narrow). Wires route behind the 2" thick plate for a clean installation. Rear cover plates enclose wires from mounting surface.
Price: $427.00
MNCCB-L or MNCCB-R
Charge controller mounting bracket, left or right. Please indicate which side of the E-panel the bracket is to be mounted. These control brackets work with all Midnite E-Panels EXCEPT THE Schneider SW E-Panel and Nottagutter.
Warranty - 5 yrs.
Price: $26.00
MNCCPDual
Dual Classic Mounting Plate used with MidNite E-Panels. Ships with the MNCCCK Close Nipple Kit, 6 Tap Tie screws for mounting the Classics and three 10 x 3/8 Flathead screws to mount the bracket to the E-Panel.
Price: $92.00