MIDNITE SOLAR PRICE LIST - May 22, 2013
PH 360.403.7207
FAX 360.691.6862 MIDNITESOLAR.COM
|
|
|
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
142.00
|
25 amp, 600 vac three-phase relays are designed for all types of loads.
Requires Heat Sink.
|
Weight: 2 Lbs.
|
|
|
$
209.00
|
75 amp, 600 vac three-phase relays are designed for all types of loads.
Requires Heat Sink.
|
Weight: 2 Lbs.
|
|
|
$
282.00
|
600 volt 100 amp DC rated Solid State Relay.
Requires Heat Sink.
|
Weight: 2 Lbs.
|
|
|
$
20.00
|
Charge controller mounting bracket. Please indicate which side of the E-panel the bracket is to be mounted. These control brackes work with all Midnite E-Panels and Nottagutter.
|
Size: 8"L x 4"W x 1"D
Boxed: 12"L x 8"W x 7"D
Weight: 2 Lbs.
|
|
|
$
7.50
|
One inch close nipple, three one inch lock nuts and two insulating bushings. Use for connecting charge controllers through the side to MidNite E-Panels or other similar enclosures.
|
Weight: 1 Lbs.
|
|
|
$
12.00
|
063" x 2.1" x 1.5" One 3/8", five .250, two .203" holes. Used on MNDC shunts for an additional bat minus battery connections.
|
Size: .063" x 2.1" x 1.5"
Weight: 1 Lbs.
|
|
|
$
36.00
|
500amp/50mV includes taptite mounting screws. Has two 8-32 tapped holes on one end to attach a bus bar. This is the industry standard shunt.
|
Weight: 2 Lbs.
|
|
|
$
2.00
|
This 1/2 in Heyco Strain Relief excepts two 1000V PV wires. Sold in bags of 25.
|
|
|
|
$
2.00 ea
|
For use anywhere you need a water tight hole plug to fill a 1/2 knock out. This is the same hole plug we use on our Nema 4X combiner boxes.
Sold in bags of 25.
|
|
|
|
$
2.00 ea
|
For use on MidNite Solar E-Panels.
NOTE: Sold in bags of 25.
|
Size: 1 3/8"L x 1 3/8"W x 1/4"D
|
|
|
$
45.00
|
This resistor is made of a ceramic tube with flat, waved alloy resistance wirewound on it.
|
Weight: 3 Lbs.
|
|
|
|
$
45.00
|
This resistor is made of a ceramic tube with flat, waved alloy resistance wirewound on it.
|
Weight: 3 Lbs.
|
|
|
$
55.00
|
This resistor is made of a ceramic tube with flat, waved alloy resistance wirewound on it.
Resistor 1500W/1.5R 1500W/1.5R
|
Weight: 3 Lbs.
|
|
|
|
$
55.00
|
This resistor is made of a ceramic tube with flat, waved alloy resistance wire-wound on it.
Resistor 3 Ohm 1500 watt 1500W/3R
|
Weight: 3 Lbs.
|
|
|
$
30.00
|
The same Din Rail mount that is used in the 120 vac E-Panels, includes mounting hardware. Holds 5 poles of din rail breakers.
|
|
|
|
$
30.00
|
The same Din Rail mount that is used in the 240 vac E-Panels, includes mounting hardware.Holds up to 6 poles of din rail breakers.
|
|
|
|
$
30.00
|
Din rail to fit the Nottagutter, includes mounting hardware.
|
|
|
|
$
85.00
|
|
|
|
|
$
239.00
|
16 gauge gray steel accepts one or two EPanels,
(wide or narrow). Wires route
behind the 2" thick plate for a clean
installation. Rear cover plates enclose
wires from mounting surface.
|
Boxed: 48"L x 31"W x 3"D
Weight: 25 Lbs.
|
|
|
$
140.00
|
White Aluminum, 120/240 slider assembly Kit for 120 volt only E-Panel
|
Weight: 2 Lbs.
|
|
|
$
40.00
|
White aluminum or gray steel.
|
Weight: 2 Lbs.
|
|
|
$
60.00
|
Gray steel, ships with two single
pole sliders not shown.
|
Weight: 2 Lbs.
|
|
|
$
60.00
|
White aluminum, ships with single pole slider.
|
Weight: 2 Lbs.
|
|
|
$
60.00
|
Gray steel, ships with single pole slider.
|
Weight: 2 Lbs.
|
|
|
$
65.00
|
White steel, ships with single pole slider.
|
Weight: 2 Lbs.
|
|
|
$
65.00
|
White steel, ships with two pole sliders not shown
|
Weight: 2 Lbs.
|
|
|
$
15.00
|
Replacement dead front for the MNPV3 and MNPV2-MC4.
|
Weight: 2 Lbs.
|
|
|
$
20.00
|
Replacement dead front for the MNPV6 and MNPV6 Disco.
|
Weight: 2 Lbs.
|
|
|
$
30.00
|
Replacement dead front for the MNPV12 and MNPV8-MC4.
|
Weight: 2 Lbs.
|
|
|
$
10.00
|
Replacement Slider for the MNPV6 Disco.
|
Weight: 1 Lbs.
|
|
|
$
10.00
|
Replacement fuse adapter for the MNPV3 and MNPV2-MC4 combiners.
|
Weight: 1 Lbs.
|
|
|
$
10.00
|
Replacement fuse adapter used with either MNPV6 or MNPV4-MC4.
|
Weight: 1 Lbs.
|
|
|
$
10.00
|
Replacement fuse adapter to be used with the MNPV12 or MNPV8-MC4. The deadfront for this fuse adapter requires two adapters.
|
Weight: 1 Lbs.
|
|
|
These kits provide all the necessary breakers and brackets to assemble your own Power
back up system. The /GEN versions have the extra
generator input transfer switch and AC inlet. Use these kits with our B, C, D and E battery enclosures.
* 175 OR 250 amp breaker MUST SPECIFY BREAKER SIZE
* AC ground bus bar
* AC input and output terminal blocks for field wiring connections
* GFCI outlet and associated 15 amp breaker wired
* Two 15 amp and one 20 amp load circuit breakers
* 50 amp AC breakers (AC input disconnect and AC bypass switch)
* 500 amp/50mV shunt for connection of battery and inverter negatives with bat negative busbar
* AC inlet for portable generator recessed on side for Large Backup Kit/gen models
* 50 amp utility/15 amp generator transfer switch on 120 VAC/gen models
* 50 amp utility/30 amp generator transfer switch on 240 VAC/gen models
* Knockout spaces for four additional AC or DC breakers on non-gen models
* Mounting hardware for Magnum or OutBack inverter
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
750.00
|
This large backup kit provides all the necessary breakers and brackets to assemble your own Power
back up system.
|
|
|
|
|
$
850.00
|
This large backup kit provides all the necessary breakers and brackets to assemble your own Power
back up system.
|
|
|
|
|
$
800.00
|
This large backup kit provides all the necessary breakers and brackets to assemble your own Power
back up system.
|
|
|
|
|
$
900.00
|
This large backup kit provides all the necessary breakers and brackets to assemble your own Power
back up system.
|
|
|
|
Products for Batteries, Monitors and Combiners ETC.
|
|
$
69.00
|
Battery Capacity Meter
|
Size: 4.5"L x 3.75"W x 1"D
Boxed: 5"L x 4"W x 2"D
Weight: 1 Lbs.
|
|
|
|
$
69.00
|
This Battery Capacity Meter allows the LEDS to be turned off while retaining the Battery Care memories.
|
Size: 4.5"L x 3.75"W x 1"D
Boxed: 5"L x 4"W x 2"D
Weight: 1 Lbs.
|
|
|
$
700.00
|
MidNite 1000amp Battery combiner box
Includes a 1000amp Positive and Negative bus bar
Includes a 1000amp 50mv Shunt
Has locations for up to 12 of our MNEDC Battery Breakers
Powder Coated Steel
|
Size: 35-1/2" L x 22" W x 9-3/4" D
Boxed: 42" L x 29" W x 16" D
Weight: 50 lbs, Shipping Weight: 55 Lbs.
|
|
|
|
2 AWG Black UL Listed Cobra X-Flex battery cable
with tin plated lugs and glue filled white or red heat shrink.
CLICK HERE FOR PRICES
|
|
|
|
|
|
2/0 Black UL Listed Cobra X-Flex battery cable
with tin plated lugs and glue filled white or red heat shrink.
CLICK HERE FOR PRICES
|
|
|
|
|
|
4/0 Black UL Listed Cobra X-Flex battery cable
with tin plated lugs and glue filled white or red heat shrink.
CLICK HERE FOR PRICES
|
|
|
|
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
1100.00
|
NEW PRODUCT
Battery Enclosure with locking door and one shelf. Outdoor 3R rain type design. Powder coated aluminum and stainless steel construction. Holds four 8D batteries. Has spaces for a single 175 or 250 amp battery breaker and up to 4 MNDC panel mount breakers (1 to 100 amps available).
Breaker not included
Ships un-assembled.
|
Size: 36"L x 28.5"W x 26.25"D
Weight: 90 Lbs.
|
|
|
|
$
1385.00
|
NEW PRODUCT
Battery Enclosure with locking door and one shelf. Outdoor 3R rain proof design. Powder coated aluminum and stainless steel construction. Holds four 8D batteries. Comes with 250 amp battery breaker, 2 of our 4/0 12 inch cables and a single 36 inch 4/0 cable for interconnecting the batteries. It also has spaces for up to 4 MNDC panel mount breakers (1 to 100 amps available). A perfect match for any of our Pre Wired Inverter systems
Ships un-assembled.
|
Size: 36"L x 28.5"W x 26.25"D
Weight: 91 Lbs.
|
|
|
$
475.00
|
Battery Enclosure with locking door and one shelf. Holds three group 31 or 27 sealed batteries per shelf side by side
or two per shelf end to end. Also holds one 8D per shelf. Two cabinets can be stacked horizontal or vertical for
expansion. Remove middle shelf for taller batteries. 2" knock outs on top and sides. Gray powder coated steel. Ships
knocked down.
Enclosure outside dimensions: 29" wide x 14.5" deep x 27.25" tall
Battery Enclosure Assembly Video
Listed by ETL for US & Canada
|
Size: 29.5"L X 27.5"W x 14.5"D
Boxed: 33"L x 30"W x 8"D
Weight: 65 Lbs.
|
|
|
$
660.00
|
NOTE: This product is being discontinued with limited quantities left.
Battery Enclosure with locking door and one shelf. Holds eight group 31 or sealed golf cart sized batteries. Gray
powder coated steel. Two cabinets can be stacked horizontal or vertical for expansion. Ships knocked down in two
cartons.
Enclosure size: 33.6" wide x 15.25" deep x 34.2" tall
Boxed size & weight: Box 1 of 2 Doors and Back 18" x 8" x 36" 40 Lbs.
Box 2 of 2 Sides, Top and Shelves.
Battery Enclosure Assembly Video
Listed by ETL for US & Canada
|
Size: 35"L x 34.5"W x 15.5"D
Boxed: Box 1: 43 x 19 x 8"
Box 2: 43 x 19 x 9"
Weight: Box 1: 64 Lb/s
Box 2: 40 Lbs.
|
|
|
$
899.00
|
MNBE-C Battery Enclosure with locking door and three shelves. Holds twelve group 31 or sealed golf cart sized batteries and even
the 14" tall PVX-3050T from Concorde. Gray powder coated steel. Two cabinets can be stacked horizontal for expansion.
Enclosure size: 36.5" wide x 16" deep x 55" tall/261 Lbs including pallet (freight truck only)
NOTE: There is an additional $100 crating fee on top of product price. Ships pre-assembled.
Listed by ETL for US & Canada for indoor use only.
|
Size: 58"L x 34"W x 15.5"D
Weight: 261 Lbs.
|
|
|
$
869.00
|
MNBE-CL16 Battery Enclosure with locking door and two shelves. Holds eight sealed L-16 batteries. Gray powder coated steel. Two cabinets can be stacked horizontal for expansion. Enclosure size: 36.5" wide x 16" deep x 55" tall/261 Lbs including pallet (truck freight only)
NOTE: There is a $100 crating fee in addition to product price. Ships pre-assembled.
Listed by ETL for US & Canada
|
Size: 58"L x 34"W x 15.5"D
Weight: 261 Lbs.
|
|
|
$
960.00
|
MNBE-C8D Battery Enclosure with locking door and four shelves. Comes complete with breaker and
interconnecting cables. Holds four 8D batteries. Gray powder coated steel. Two cabinets can be stacked horizontal for expansion. Enclosure size: 36.5" wide x 16" deep x 55" tall/261 Lbs including pallet (freight truck only)
NOTE: There is an additional $100 crating fee on top of product price. Ships pre-assembled.
Listed by ETL for US & Canada
|
Size: 58"L x 34"W x 15.5"D
Weight: 261 Lbs.
|
|
|
$
689.00
|
Our Best Value! Battery Enclosure with locking door and two shelves. MNBE-D holds 8 GVX3050T or 8 golf cart or 8 group 31 batteries. With the optional third shelf, the MNBE-D holds 12 group 31 batteries. The image shows 8 GVX3050T batteries. Ships knocked down in two boxes.
Battery Enclosure Assembly Video
Listed by ETL for US & Canada
|
Size: 41.5"L x 34"W x 15.5"D
Boxed: Box 1: 43 x 19 x 8"
Box 2: 43 x 19 x 9"
Weight: Box 1 - 48 Lb/s
Box 2 - 69 Lbs.
|
|
|
$
949.00
|
Rain tight aluminum battery enclosure with locking door and two shelves. MNBE-D holds 8 GVX3050T or 8 golf cart or 8 group 31 batteries. Ships knocked down in two boxes.
Battery Enclosure Assembly Video
|
Size: 41.5"L x 34"W x 15.5"D
Boxed: Box 1: 43 x 19 x 8"
Box 2: 43 x 19 x 9"
Weight: Box 1 - 30 Lb/s
Box 2 - 52 Lbs.
|
|
|
$
89.00
|
Extra shelf for MNBE-C, MNBE-D, or MNBE-E
|
|
|
|
$
10.00
|
Battery Enclosure Key works with all MidNite Solar battery enclosures.
|
Size: 2"L x 1"W x 1/8"D
|
|
|
$
49.00
|
Fan bracket fits inside the MNBE-C or D battery enclosure. It gives a way to add a 120mm square boxer fan to our outdoor enclosure.
|
Weight: 2 Lbs.
|
|
|
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
69.00
|
63 amp 150VDC din rail mount DC ground fault protector (NRTL listed breaker assy).
NEC2008 requires DC-GFP’s on all solar installations.
10,000 AIC
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers hold 100% rated current independent of ambient temperature.
Listed for US & Canada
|
Weight: 1 Lbs.
|
|
|
$
69.00
|
80 amp 150VDC panel mount DC ground fault protector (NRTL listed breaker assy)
1/2 amp trip mechanism connects between battery negative and earth ground
NEC2008 requires DC-GFP’s on all solar installations.
10,000 AIC
Breaker Torque Value: 30 In-Lbs (3.4NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers hold 100% rated current independent of ambient temperature.
Listed for US & Canada
|
Weight: 1 Lbs.
|
|
|
$
129.00
|
100 amp 150VDC panel mount Dual DC ground fault protector (NRTL listed breaker assy)
Breaker Torque Value: 30 In-Lbs (3.4NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
|
Weight: 1 Lbs.
|
|
|
$
119.00
|
50 amp 300VDC ground fault protector din rail mount (NRTL listed breaker assembly).
10,000 AIC
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Listed for US & Canada
|
Boxed: 9 x 5 x 4"
Weight: 2 Lbs.
|
|
|
$
17.00
|
Purchase in quantity of 12 per box.
10, 15, & 20 amp 120VAC branch circuit rated 489A din rail mount.
10,000 AIC
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers hold 100% rated current independent of ambient temperature.
Listed for US & Canada
|
Boxed: 13mm wide
Weight: 0.5 Lbs.
|
|
|
$
17.00
|
Purchase in quantity of 12 per box.
30, 40, 50, 60 amp 120VAC Supplementary protection 1077 din rail mount.
3,000 AIC
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Listed for US & Canada
|
Boxed: 13mm wide
Weight: 0.5 Lbs.
|
|
|
$
34.00
|
Purchase in quantity of 6 per box.
15, 20 amp din rail mount 120/240 VAC Branch circuit rated 489 two pole. 10,000 AIC
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers hold 100% rated current independent of ambient temperature.
Listed for US & Canada
|
Boxed: 26mm wide
Weight: 1 Lbs.
|
|
|
|
$
34.00
|
Purchase in quantity of 6 per box.
30, 50, 60 amp din rail mount 120/240 VAC Supplementary protection 1077 two pole.
3,000 AIC
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Listed for US & Canada
|
Boxed: 26mm wide
Weight: 1 Lbs.
|
|
|
$
17.00
|
Purchase in quantity of 12 per box.
White 15, 20, 30, 50, 60 amp din rail mount 277VAC Supplementary protection 1077 single pole.
3,000 AIC
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
15 amp 30, 50, 60 Listed for US & Canada
|
Weight: 0.5 Lbs.
|
|
|
$
34.00
|
Purchase in quantity of 6 per box.
White 30, 50, 60 amp din rail mount 277VAC Supplementary protection 1077 double pole.
3,000 AIC
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Listed for US & Canada
|
Weight: 1 Lbs.
|
|
|
$
54.00
|
Purchase in quantity of 4 per box.
White or black 15, 30, 50 amp din rail mount 277VAC Supplementary protection 1077 triple pole.
3,000 AIC
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Listed for US & Canada
|
Boxed: 1.5" wide
Weight: 1.5 Lbs.
|
|
MNEDC5, MNEDC10, MNEDC15, MNEDC20, MNEDC30, MNEDC40, MNEDC50, MNEDC60, MNEDC70, MNEDC80, MNEDC90, MNEDC100 Breaker
|
$
20.00
|
5, 10, 15, 20, 30, 40, 50, 60, 70, 80, 90, 100 amp 150VDC Panel Mount.
10,000 AIC
Breaker Torque Value: 30 In-Lbs (3.4NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Listed for AC & DC in US & Canada
|
Boxed: 1/2 " studs 3/4" wide
Weight: 0.5 Lbs.
|
|
|
$
54.00
|
Purchase in quantity of 12 per box.
125amp 125VDC Panel Mount
AIC 10,000 at 125VDC
Breaker Torque Value: 30 In-Lbs (3.4NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Listed for US & Canada
|
Boxed: 1/4 studs 1" wide
Weight: 2 Lbs.
|
|
|
$
109.00
|
Purchase in quantity of 3 per box.
125VDC 3/8" studs 1.5"
AIC 50,000 at 125VDC
Breaker Torque Value: 15 Ft-Lbs (20.4NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Listed for US & Canada
|
Weight: 3 Lbs.
|
|
|
$
40.00
|
Purchase in quantity of 18 per box.
60 or 80 Amp 300 VDC panel mount breaker.
10,000 AIC
Breaker Torque Value: 30 In-Lbs (3.4NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Listed for US & Canada
|
Weight: 1 Lbs.
|
|
|
$
119.00
|
20/50 Amp 300 VDC 4 pole din rail mount breaker.
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
Listed for US & Canada
|
Weight: 1 Lbs.
|
|
MNEPV1, MNEPV2, MNEPV3, MNEPV4,
MNEPV5, MNEPV6, MNEPV7, MNEPV8, MNEPV9,
MNEPV10, MNEPV12, MNEPV15, MNEPV20, MNEPV30, MNEPV40, MNEPV50, MNEPV60, MNEPV63
|
$
14.75
|
Purchase in quantity of 12 per box.
150VDC din rail mount breaker (13mm wide).
Always in stock!
MNEPV breakers are the same as CBI QY breakers except the standard used is inadequate for the solar industry. MidNite breakers have been evaluated by ETL to 150VDC and are listed for US and Canada. All of the NRTL listings still apply. Breakers ordered under the CBI part numbering system will not be listed for 150VDC and in many cases are not suitable for the solar industry.
150VDC ETL listed in the US and Canada
10,000 AIC
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure
Listed for US & Canada
|
Boxed: 13mm wide
Weight: 0.5 Lbs.
|
|
|
$
54.00
|
Purchase in quantity of 10 per box.
80 or 100 amp Din rail mount breaker. MNEPV breakers are the same as CBI QY breakers except the standard used is inadequate for the solar industry. MidNite breakers have been evaluated by ETL to 150VDC and are listed for US and Canada. All of the NRTL listings still apply. Breakers ordered under the CBI part numbering system will not be listed for 150VDC and in many cases are not suitable for the solar industry.
Accepts up to #2 wire.
10,000 AIC.
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Listed for US & Canada
|
Boxed: 26mm wide
Weight: 1 Lbs.
|
|
|
$
34.00
|
Purchase in quantity of 10 per box.
7, 10, 12, 15, 20, 30, 50 amp 300VDC din rail mount breaker.
10,000 AIC
MNEPV breakers are the same as CBI QY breakers except the standard used is inadequate for the solar industry. MidNite breakers have been evaluated by ETL to 300VDC and are listed for US and Canada. All of the NRTL listings still apply. Breakers ordered under the CBI part numbering system will not be listed for 300VDC and in many cases are not suitable for the solar industry.
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
All MidNite circuit breakers hold 100% rated current independent of ambient temperature.
Listed for US & Canada
|
Weight: 1.5 Lbs.
|
|
|
$
119.00
|
16 or 20 Amp 600 VDC Din Rail mount breaker. All MidNite circuit breakers can be used at 100% rated current when mounted in a MidNite enclosure.
Breaker Torque Value: 20 In-Lbs (2.3NM)
Breaker and Busbar Torque Values
Listed for US & Canada
|
Weight: 2 Lbs.
|
|
|
$
6.00
|
1" to 3/4" Breaker Adapter
Available to distributors only in a 24 pack.
|
Weight: 0.5 Lbs.
|
|
|
$
19.00
|
The Breaker Protector will keep the 175 or 250 Amp Breaker from being accidentally hit.
|
Boxed: 4" x 6" x 4"
Weight: 1 Lbs.
|
|
|
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
2.50 Ea
|
These busbar insulator covers help protect from accidental shorts.
MN1/0LBBC-W (Long white)
MN1/0SBBC-W (Short white)
MN1/0LBBC-R (Long red)
MN1/0SBBC-R (Short red)
MN1/0LBBC-G (Long green)
MN1/0SBBC-G (Short green)
MN1/0LBBC-BLK (Long black)
MN1/0SBBC-BLK (Short black)
|
Weight: 1 Lbs.
|
|
|
$
99.00
|
8 studs for multiple paralleled battery strings. Breaker is sold separately.
Breaker and Busbar Torque Values
|
Weight: 2 Lbs.
|
|
|
$
75.00
|
280 amps, Same busbar used in the Nottagutter. Five, 5/16 studs for battery connections.
Comes with auxiliary terminal busbar for six small wires #14-1/0.
Breaker and Busbar Torque Values
|
Weight: 1 Lbs.
|
|
|
$
28.00
|
1/8" thick tin plated copper busbar for use with the MNPV12 combiner.
Breaker and Busbar Torque Values
|
Boxed: 3 x 4 x 5"
Weight: 2 Lbs.
|
|
|
$
30.00
|
1/8" thick tin plated copper accommodates up to three 300VDC MidNite circuit breakers.
Breaker and Busbar Torque Values
|
Boxed: 3 x 4 x 5"
Weight: 2 Lbs.
|
|
|
|
$
30.00
|
1/8" thick tin plated copper accommodates up to three 300VDC MidNite circuit breakers.
Breaker and Busbar Torque Values
|
Boxed: 5"L x 4"W x 3"D
Weight: 2 Lbs.
|
|
|
$
13.00
|
This .093" thick copper bus has three fingers spaced at 1/2" (13mm) intervals
one box lug is provided to accommodate 14-1/0 AWG wire.
Breaker and Busbar Torque Values
|
Weight: 1 Lbs.
|
|
|
$
15.00
|
MNPV6 BUSBAR This .093" thick copper bus has six fingers spaced at 1/2" (13mm) intervals
Two box lugs are provided to accommodate 14-1/0 AWG wire.
Breaker and Busbar Torque Values
|
Weight: 1 Lbs.
|
|
|
$
13.00
|
This .063" thick copper bus has four fingers spaced at 3/4" (19mm) intervals
One box lug is provided that accommodates 14-1/0 AWG wire.
Breaker and Busbar Torque Values
|
Weight: 1 Lbs.
|
|
|
$
12.00
|
MidNite ground busbar 3.45" long with Green screws! Two 1/0 & seven #6 wire slots. Comes with mounting screws. Made in USA, NRTL recognized.
Breaker and Busbar Torque Values
|
Weight: 1 Lbs.
|
|
|
$
10.00
|
2.3" long. Two 1/0 & four #6 wire slots. 180 amps. Comes with mounting screw& nut #10-32 x 7/8". Made in USA, NRTL recognized.
Breaker and Busbar Torque Values
|
Weight: 1 Lbs.
|
|
|
$
13.00
|
Without insulators. Comes with 10-32 screws. For use with the MidNite Shunt. Busbar 4.63" UL and CSA recognized. 180 amps. Made in USA.
|
|
|
|
$
15.00
|
(Midnite Short Busbar) Shorter version of the insulated bus bars. These are useful for PV+ input on the narrow OB E-Panel and for a separate PV- bus bar for
charge controllers that require them. 180 amps. Four #6 and two 1/0 wire slots. Listed for US and Canada.
Breaker and Busbar Torque Values
|
Weight: 1 Lbs.
|
|
|
$
17.00
|
Four 1/0 & eleven #6 useable wire slots. 180 amps. Comes with two lengths of 10-32 screws. Both copper and aluminum wire is acceptable for use with these busbars. Listed for US and Canada
Breaker and Busbar Torque Values
|
Weight: 1 Lbs.
|
|
|
$
49.00
|
Mounts on 500 shunt. Same busbar used in the Nottagutter. Four battery cable studs and six position aux terminal busbar.
Shunt sold separately.
Breaker and Busbar Torque Values
|
Weight: 1 Lbs.
|
|
CHARGE CONTROLLERS FOR SOLAR, WIND, HYDRO
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
Note: All combiner enclosures will accept MidNite Solar MNSPD lightning arrestors.
Note: See www.midnitesolar.com/documents/dimensiondrawings/ for enclosure size and locations.
Note: All enclosures can accept bulkhead mount MC connectors for faster on roof time.
Note: Call for pricing on factory installed MC bulkhead connectors.
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
99.00
|
Enclosure only
(For 150 VDC charge controllers and 600 VDC grid tie inverters)
Gray aluminum type 3R rainproof enclosure with deadfront, will accept three 150VDC (MNEPV)
breakers or two 600 VDC fuse holders.
Listed by ETL for US & Canada
|
Size: 10.5"L x 4.5"W x 3.5"D
Boxed: 11"L x 5"W x 4"D
Weight: 2 Lbs.
|
|
|
$
119.00
|
Enclosure only
(For 150 VDC charge controllers and 600 VDC grid tie inverters)
(The most popular PV combiner in North America.) Gray aluminum type 3R rainproof enclosure with insulating dead front, will accept six 150VDC breakers or 4 600VDC fuse holders.
Listed by ETL for US & Canada
|
Size: 13.5"L x 8"W x 3.5"D
Boxed: 14"L x 9"W x 4"D
Weight: 4 Lbs.
|
|
|
$
129.00
|
Enclosure only
(For 200 and 250 VDC charge controllers) Gray aluminum type 3R rainproof enclosure with insulating dead front, will accept three 300 VDC MidNite Solar breakers.
Breakers sold separately.
Listed by ETL for US & Canada
|
Size: 13.5"L x 8"W x 3.5"D
Boxed: 14"L x 9"W x 4"D
Weight: 5 Lbs.
|
|
|
$
179.00
|
Enclosure only
NOW SHIPPING WITH BOTH TWIN DUAL PV MINUS AND DUAL PLUS BUSBARS
(For 150 VDC charge controllers and 600 VDC grid tie inverters) Gray aluminum type 3R rainproof enclosure with insulating dead front, will accept 12 150VDC breakers or 10 600VDC fuse holders. Can support two inverters of up to 5 strings each, or a transformerless inverter of up to 5 strings.
Listed by ETL for US & Canada
|
Size: 14.5"L x 12W" x 3.5"D
Boxed: 16"L x 14"W x 5"D
Weight: 8 Lbs.
|
|
|
$
189.00
|
Enclosure only
(For 200 and 250VDC charge controllers)
Gray aluminum type 3R rainproof enclosure with insulating dead front, will accept 6 300VDC breakers.
Listed by ETL for US & Canada
|
Size: 14.5"L x 12W" x 3.5"D
Boxed: 16"L x 14"W x 5"D
Weight: 8 Lbs.
|
|
|
$
399.00
|
Enclosure only
This 3R enclosure is for up to 100,000 watt 600 VDC grid tie inverters.
Listed by ETL for US & Canada
|
Size: 21.75"L x 16"W x 3"D
Boxed: 22"L x 18"W x 5"D
Weight: 13 Lbs.
|
|
|
$
399.00
|
Enclosure only
This 3R MNPV16-24 PV combiner can hold up to 24 single pole 150VDC breakers.
Listed by ETL for US & Canada
|
Size: 21.75"L x 16"W x 3"D
Boxed: 22"L x 18"W x 5"D
Weight: 13 Lbs.
|
|
|
$
399.00
|
Enclosure only
This 3R enclosure is for use with 300VDC breakers for high powered, high voltage off-grid applications.
Listed by ETL for US & Canada
|
Size: 21.75"L x 16"W x 3"D
Boxed: 22"L x 18"W x 5"D
Weight: 13 Lbs.
|
|
COMBINER’S - PRE-WIRED
|
|
$
877.00
|
The MNPV6HV-MC4 Nema 4X pre-wired combiner is rated for outdoor use. Designed for combining PV strings up to 600 vdc using standard MC4 connectors. Features include a 3 pole 100 amp switch, 125 amp rated busbars, 6 MNTS Fuse holders, 6- 15a/600v fuses and an MNSPD600 Lightning surge Arrester.
|
|
|
|
$
189.00
|
This 3R pre-wired MNPV2 combiner is rated for outdoor use. Designed for combining high voltage strings using standard 10mm x 38mm fuses up to 60 amps total.
Pre-Wired Ad
Listed by ETL for US & Canada
|
Size: 10.5"L x 4.5"W x 3.5"D
Boxed: 11"L x 5"W x 4"D
Weight: 3 Lbs.
|
|
|
$
209.00
|
This 3R pre-wired MNPV4 combiner is rated for outdoor use. Designed for combining high voltage strings using standard 10mm x 38mm fuses up to 80 amps total.
Pre-wired Ad
Listed by ETL for US & Canada
|
Size: 10.5"L x 4.5"W x 3.5"D
Boxed: 11"L x 5"W x 4"D
Weight: 5 Lbs.
|
|
|
$
359.00
|
This 3R pre-wired MNPV8 combiner is rated for outdoor use. Designed for combining high voltage strings using 10mm x 38mm fuses up to 200 amps total.
Pre-wired Ad
Listed by ETL for US & Canada
|
Size: 13.5"L x 8"W x 3.5"D
Boxed: 14"L x 9"W x 4"D
|
|
|
$
268.00
|
This 3R pre-wired MNPV4-MC4-LV combiner is rated for outdoor use.
Listed by ETL for US & Canada
|
Size: 10.5"L x 4.5"W x 3.5"D
Boxed: 11"L x 5"W x 4"D
Weight: 6 Lbs.
|
|
|
$
285.00
|
This 3R pre-wired MNPV6-MC4-LV combiner is rated for outdoor use.
Listed by ETL for US & Canada
|
Size: 13.5"L x 8"W x 3.5"D
Boxed: 14"L x 9"W x 4"D
Weight: 6 Lbs.
|
|
|
$
715.00
|
This disconnecting combiner is for transformerless type inverter installations where both PV positive and negative from each array will be disconnected when breakers are switched off. Comes with two surge protection devices. 150V circuit breakers are available from 16 to 20A 600V.
|
|
|
COMBINERS, DISCONNECTING (LOAD BREAK RATED)
Disconnects are all Load Break rated
|
|
$
204.00
|
Enclosure only - NOT COMPATIBLE WITH THE BIRDHOUSE.
This 3R MNPV6 DISCO combiner is one in a series of disconnecting PV combiners from MidNite Solar. This model will support several different configurations. You can use 6 of our 150 volt DC breakers and included buss-bar for a 6 string disconnecting combiner. You also will be able to install 1 of our 600 volt DC breakers making a nice grid tie disconnect.
MNPV6 3R Disco Assy Instructions
Listed by ETL for US & Canada
|
Size: 13.2"L x 8"W x 6.2"D
Boxed: 15"L x 9"W x 7.25"D
Weight: 6 Lbs.
|
|
|
|
$
214.00
|
Enclosure only - NOT COMPATIBLE WITH THE BIRDHOUSE.
This 3R MNPV6-250 DISCO combiner is one in a series of disconnecting PV combiners from MidNite Solar. This model includes the buss-bar to use up to 3 of our 300 volt DC breakers as a 3 string DC combiner. You can also purchase a second buss-bar (MNPV12-250) and use this with 3 of our 240 volt AC breakers to combine up to 3 strings of 240 volt micro inverters.
MNPV6 3R Disco Assy Instructions
Listed by ETL for US & Canada
|
Size: 13.2"L x 8"W x 6.2"D
Boxed: 15"L x 9"W x 7.25"D
Weight: 6 Lbs.
|
|
|
|
$
239.00
|
Enclosure only - NOT COMPATIBLE WITH THE BIRDHOUSE.
This 3R enclosure includes 2 busbars. Can use up to 3 of our 240 VAC breakers to combine up to 3 strings of 240 volt micro inverters.
|
Size: 13.2"L x 8"W x 6.2"D
Boxed: 15"L x 9"W x 7.25"D
Weight: 6 Lbs.
|
|
COMBINERS, DISCONNECTING - REMOTE DISCONNECT CAPABLE (LOAD BREAK RATED)
Disconnects are all Load Break Rated
|
|
$
429.00
|
MNPV4HV Disco 3R - Basic Disconnecting Combiner has 80 amp busbars, 100 amp load break rated switch has two poles in series.
MNPV4 Disco Assy Instructions
Disconnecting PV Combiners Video
MNPV4HV Disco Combiner Video
Read PDF on the Discos - 11 MB
|
Size: 13.7"L x 10.4"W x 4.4"D
Boxed: 19"L x 16"W x 5"D
Weight: 8 Lbs.
|
|
|
$
589.00
|
MNPV4HV Disco 3R - Deluxe Disconnecting Combiner has 80 amp busbars, 100 amp load break rated switch and a third pole which is the feedback micro switch.
MNPV4 Disco Assy Instructions
Disconnecting PV Combiners Video
MNPV4HV Disco Combiner Video
Read PDF on the Discos - 11 MB
|
Size: 13.7"L x 10.4"W x 4.4"D
Boxed: 19"L x 16"W x 5"D
Weight: 10 Lbs.
|
|
|
$
799.00
|
MNPV6HV Disco 4X PV Disconnecting Combiner, 3 poles, 125 amp busbars, 100 amp load break rated switch.
MNPV6 4X Disco Assy Instructions
Disconnecting PV Combiners Video
Read PDF on the Discos - 11 MB
|
Size: 16.8"L x 12.4"W x 5.6"D
Boxed: 21"L x 17"W x 6"D
Weight: 14 Lbs.
|
|
|
$
825.00
|
MNPV8HV Disco 3R PV Disconnecting Combiner, 5 poles, 80 or 160 amp busbars depending on how they are configured. Switch is a 100 amp load break rated or 175 amps load break rated depending on configuration.
MNPV8HV Disconnecting Combiner Video
Disconnecting PV Combiners Video
MNPV8HV Assembly Instructions
Two Inverter Conversion
NON-Isolated Conversion
Parallel Conversion
Read PDF on the Discos - 11 MB
|
Size: 18.5"L x 14"W x 4.6"D
Boxed: 24"L x 19"W x 6"D
Weight: 16 Lbs.
|
|
|
$
969.00
|
MNPV8HV Disco 4X PV Disconnecting Combiner, 5 poles, 80 or 160 amp busbars depending on how they are configured. Switch is 100 amp load break rated or 175 amps depending on configuration.
Disconnecting PV Combiners Video
MNPV8HV Assembly Instructions
Two Inverter Conversion
NON-Isolated Conversion
Parallel Conversion
Read PDF on the Discos - 11 MB
|
Size: 19.5"L x 14.8"W x 5.8"D
Boxed: 24"L x 19"W x 6"D
Weight: 18 Lbs.
|
|
|
$
1399.00
|
MNPV16HV Disco 4X PV Disconnecting Combiner, 5 poles, 100 amp load break rated or 175 amps load break rated for busbars and switch.
Disconnecting PV Combiners Video
MNPV16HV Assy Instructions
Two Inverter Conversion
NON-Isolated Conversion
Parallel Conversion
Read PDF on the Discos - 11 MB
|
Size: 21.6"L x 19.9"W x 5.8"D
Weight: 27 Lbs.
|
|
|
$
750.00
|
Birdhouse - Emergency Disconnect Switch
NOTE: FOR THE BIRDHOUSE TO WORK WITH YOUR DISCONNECTING COMBINER YOU WILL NEED TO PURCHASE THE POWER SUPPLY BOARD MNDiscoPSB.
|
Size: 12.1"L x 8.3"W x 4.6"D
Boxed: 16"L x 12"W x 7"D
Weight: 5 Lbs.
|
|
|
$
150.00
|
Power Supply Board for Disco Combiners in connection to the Birdhouse.
|
Boxed: 9.5"L x 4"W x 3.25"D
Weight: 2 Lbs.
|
|
|
$
1.39 per ft.
|
MNCAT5-600 USE-2 Cable $1.39 per ft.
|
Boxed: Depends on amount ordered
|
|
|
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
799.00
|
NOTE: This product is being discontinued with limited quantities left.
Works with all Apollo inverters
Listed by ETL for US & Canada
|
Boxed: 18 x 11 x 28"
Weight: 42 Lbs.
|
|
|
|
$
799.00
|
NOTE: This product is being discontinued with limited quantities left.
Works with all Apollo inverters
Listed by ETL for US & Canada
|
Boxed: 18 x 11 x 28"
Weight: 42 Lbs.
|
|
|
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
579.00
|
All included AC bypass and input disconnect breakers are rated for 277 VAC. Export versions
of our standard E-Panels are made using Blue and Brown wire and terminal bus bar insulators.
Add an "E" to the end of any model number to create an E-Panel suited for Africa, Australia,
New Zealand or Europe. Prices are the same as regular E-Panels.
Example: MNE125ST-R-E (Shown) Refer to the North American versions for size, weight and price.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 29 Lbs.
|
|
|
The Magnum E-Panel comes with inverter breaker, 2/0 inverter cables, pre-wired AC input and bypass, 500amp 50mV shunt, AC terminal blocks, 100 amp DC positive and DC negative bus bars, PV input bus bar, din rails, 3 panel mount breaker knockouts, Ground bus bar, DC wiring cover, top shield, remote display mounting bracket, wall mounting brackets, charge controller bracket and lots of hardware and grommets.
ETL listed for the US and Canada.
Note: Left hand units are standard. For E-Panels built as Right hand units, an "-R" must be added to the end of the model number. Right Hand versions have the hinge on the right, circuit breakers on the right and charge control bracket on the left.
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
619.00
|
Gray steel with 175A/125VDC inverter breaker for RD1824, RD2824, RD2624E and MS2712E
Here is a stacked pair wiring diagram: Wiring Diagram 2
Evolution of the E-Panel
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 39 Lbs.
|
|
|
|
$
619.00
|
Gray steel with 250A breaker for MS4024/ MS2812/MS2012/MS4124E & RD series.
Here is a stacked pair wiring diagram: Wiring Diagram 2
Evolution of the E-Panel
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 39 Lbs.
|
|
|
$
549.00
|
Designed for the Magnum Energy MM series inverters.
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 22 Lbs.
|
|
|
$
659.00
|
White aluminum with 175a breaker for MS4024/MS2812/MS2012/MS4124E & RD series.
Evolution of the E-Panel
NOTE: Not available in right hand versions
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 31 Lbs.
|
|
|
|
$
659.00
|
White aluminum with 250A breaker for MS4024/MS2812/MS2012/MS4124E & RD series.
Evolution of the E-Panel
NOTE: Not available in right hand versions
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 31 Lbs.
|
|
|
$
75.00
|
Gray steel right hand hinge door with LH charge control mounting bracket for wide chassis.
|
Size: 25"L x 16"W x 1/2"D
Boxed: 30"L x 17"W x 1"D
Weight: 8 Lbs.
|
|
E-PANEL - MAGNUM PAE 120/240VAC
The AE series comes with all the regular E-Panel features plus terminal bus bars for 120/240VAC input and
output.
NOTE: 120 VAC E-Panels cannot be adapted for use with 120/240 inverters.
ETL listed for the US and
Canada
Note: Left hand units are standard. For E-Panels built as Right hand units, an "-R" must be added to the end of the model number. Right Hand versions have the hinge on the right, circuit breakers on the right and charge control bracket on the left.
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
799.00
|
White steel for 120/240VAC in & out for MS4448-PAE
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 5"D
Boxed: 28"L x 19"W x 11"D
Weight: 42 Lbs.
|
|
|
|
$
799.00
|
White steel for 120/240VAC in & out for MS4024-PAE
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 5"D
Boxed: 28"L x 19"W x 11"D
Weight: 42 Lbs.
|
|
|
Note: For E-Panels built as Right hand units, add a "-R" to the end of the model number instead of the -L. Right Hand versions have the hinge on the right, circuit breakers on the right and charge control bracket on the left.
Note: The Stretched version (STS) utilizes the 14.5" wide chassis to provide 5" additional wiring room.
Note: All E-Panels now come with a side plate that accommodates up to three panel mount breakers like the MNEDC80 or two panel mount breakers and DC-GFP80. These side plates also accommodate the OB Flexnet battery status monitor on 14.5 chassis versions. All OB E-Panels come with a Mate mounting bracket, PV+ busbar and 100 amp bat + busbar.
Note: The narrow Outback E-panels do not accommodate the OB surge arrester.
Note: All Outback E-Panels work with FX, VFX, GFX, and GVFX inverters.
Note: Add suffix (-E) for export versions wired with blue and brown wire. 277 VAC breakers are already standard on all E-Panels.
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
509.00
|
Gray steel with 125A/125 VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 28 Lbs.
|
|
|
|
$
549.00
|
Gray steel with 175A/125 VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 29 Lbs.
|
|
|
|
$
549.00
|
Gray steel with 250A/125 VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 29 Lbs.
|
|
|
$
639.00
|
Stretched aluminum OB with FM/60/80/Classic mounting on the door. Left hand hinge standard, Right hand hinged optional (Right hand order P/N MNE250AL-PLUS-R)
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 24 Lbs.
|
|
|
|
$
679.00
|
Stretched aluminum OB with FM/60/80/Classic mounting on the door. Left hand hinge standard, Right hand hinged optional (Right hand order P/N MNE250AL-PLUS-R)
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 27 Lbs.
|
|
|
|
$
679.00
|
Stretched aluminum OB with FM/60/80/Classic mounting on the door. Left hand hinge standard, Right hand hinged optional (Right hand order P/N MNE250AL-PLUS-R)
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 27 Lbs.
|
|
|
$
549.00
|
White aluminum with 125A/125VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 19 Lbs.
|
|
|
|
$
579.00
|
White Alum with 175A/125VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 23 Lbs.
|
|
|
|
$
579.00
|
White Alum with 250A/125VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 23 Lbs.
|
|
|
$
579.00
|
Stretched Gray steel with 125A/125VDC breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 38 Lbs.
|
|
|
|
$
619.00
|
Stretched Gray steel with 175A/125VDC breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 39 Lbs.
|
|
|
|
$
619.00
|
Stretched Gray steel with 250A/125VDC breaker. Right hand version available.
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 19"W x 11"D
Weight: 39 Lbs.
|
|
|
$
75.00
|
Gray Steel RH door with LH Chrg Cntrl Brkt for narrow OB chassis
|
Size: 25"Lx11"W x 1/2"D
Boxed: 30"L x 12"W x 1"D
Weight: 6 Lbs.
|
|
|
$
75.00
|
White aluminum RH door with left hand charge control bracket for narrow OB chassis.
|
Size: 25"L x 11"W x 1/2"D
Boxed: 30"L x 12"W x 1"D
Weight: 4 Lbs.
|
|
|
$
80.00
|
Gray steel RH door with LH Chrg Cntrl Brkt for wide OB chassis.
|
Size: 25"L x 16"W x 1/2"D
Boxed: 30"L x 17"W x 1"D
Weight: 8 Lbs.
|
|
|
|
$
20.00
|
Charge controller mounting bracket. Please indicate which side of the E-panel the bracket is to be mounted.
|
Size: 8"L x 4"W x 1"D
Boxed: 12"L x 8"W x 7"D
Weight: 2 Lbs.
|
|
|
|
|
$
1295.00
|
This MidNite Solar RADIAN Single E-Panel is designed for single inverter installations. All Breakers on the upper left hand side. Brushed stainless steel door that matches the Radian inverter. Enclosure made from powder coated steel.
|
Size: 17" L x 16" W x 8.5" D
Boxed: 21" L x 21" W x 13" D
Weight: 38 lbs, Shipping Weight: 40.5 Lbs.
|
|
|
|
$
1495.00
|
This MidNite Solar RADIAN Master E-Panel is the left hand E-Panel in a dual inverter system. Brushed stainless steel door that matches the Radian inverter. Enclosure made from powder coated steel.
|
Size: 17" L x 16" W x 8.5" D
Boxed: 21" L x 21" W x 13" D
Weight: 38 lbs, Shipping Weight: 40.5 Lbs.
|
|
|
|
$
1150.00
|
This MidNite Solar RADIAN Slave E-Panel will be on the right hand side, in a dual inverter system. Brushed stainless steel door that matches the Radian inverter. Enclosure made from powder coated steel.
|
Size: 17" L x 16" W x 8.5" D
Boxed: 21" L x 21" W x 13" D
Weight: 38 lbs, Shipping Weight: 40.5 Lbs.
|
|
|
|
$
20.00
|
Charge controller mounting bracket. Please indicate which side of the E-panel the bracket is to be mounted.
These control brackes work with all Midnite E-Panels and Nottagutter.
|
Size: 8" L x 4" W x 1" D
Boxed: 12" L x 8" W x 7" D
Weight: 2 Lbs.
|
|
|
$
59.00
|
Dual Classic Mounting Plate used with MidNite E-Panels. Ships with the MNCCCK Close Nipple Kit and three 10 x 3/8 Flathead screws.
|
Weight: 3 Lbs.
|
|
|
|
|
$
1671.00
|
The MNE250SMA-AC-SINGLE master includes the Manual input/output bypass system along with separate AC input and output breakers. The Automatic Grid tie Bypass relay is installed as well. This E-Panel can be used in conjunction with a Sunny Island inverter as part of an AC Coupled system. Comes with a 250 battery disconnect breaker and inverter cables. Pre-wired with AC input and output wiring.
|
Boxed: 25"L x 23"W x 14"D
Weight: 40 Lbs.
|
|
|
$
1100.00
|
Additional Wiring Diagram
SMA SINGLE WITH ONE CLASSIC OFF GRID
The MNE250SMA-OG-SINGLE The Off Grid Single is designed for a single Sunny Island off grid system. It includes the Manual input/output bypass system along with separate AC input and output breakers. Comes with a 250 battery disconnect breaker and inverter cables. Pre-wired with AC input and output wiring
|
Boxed: 25"L x 23"W x 14"D
Weight: 40 Lbs.
|
|
|
$
1250.00
|
Additional Wiring Diagrams
SMA DUAL OFF GRID NO CC For Label
SMA DUAL OFF GRID 2 CLASSICS
SMA Dual AC COUPLED 3 SUNNYBOYS
The MNE250SMA-OG/AC DM The Dual Master E-Panel works with 1 of the MNE250SMA-Slave E-Panel’s to create a 120/240 VAC AC coupled or Off Grid system. The MNE250SMA-OG/AC DM includes the 120/240 vac input/output bypass system. Terminals are provided for hookup to leg 2 from the Slave E-Panel. Comes with 250A battery disconnect breaker and inverter cables. Pre-wired with AC input and output wiring for leg 1 (master) inverter. (One slave E-Panel is required for 120/240.)
|
Boxed: 25"L x 23"W x 14"D
Weight: 40 Lbs.
|
|
|
$
1340.00
|
The MNE250SMA-Quad Mstr This E-Panel works with 3 of the MNE250SMA-Slave E-Panels to create a Quad stack of Sunny Islands. The MNE250SMA-Quad Mstr master includes the Quad input/output bypass system. This E-Panel can be used in conjunction with a Sunny Island inverter as part of a Quad off-grid, battery backup or AC Coupled system. Terminals are provided for hookup to leg 1 + 2 in the Slave E-Panels. Comes with 250A battery disconnect breaker and inverter cables. Pre-wired with AC input and output wiring for leg 1 (master) inverter. (Three slaves are also required for Quad system.)
|
Boxed: 25"L x 23"W x 14"D
Weight: 40 Lbs.
|
|
|
|
$
1365.00
|
Additional Wiring Diagram
SMA 3 phase NO TRANSFER SWITCH
The MNE250SMA-3PH Master E-Panel works with 2 of the MNE250SMA-Slave E-Panels to create a 3 phase system. The MNE250SMA-3PH 3 phase master includes the 3 phase input/output bypass system. This E-Panel can be used in conjunction with a Sunny Island inverter as part of a 3 phase off-grid, battery backup or AC Coupled system. Terminals are provided for hookup to leg 2 and leg 3 E-Panels. Comes with 250A battery disconnect breaker and inverter cables. Pre-wired with AC input and output wiring for leg 1 (master) inverter. (Two slaves are also required for 3 phase.)
|
Boxed: 25"L x 23"W x 14"D
Weight: 40 Lbs.
|
|
|
$
1050.00
|
Additional Wiring Diagram
SMA 3 phase NO TRANSFER SWITCH
Companion E-Panel for dual, triple and quad Sunny Island inverter systems. The Slave E-Panel is the same part number for all multiple SMA E-Panel systems regardless of off-grid, AC coupled, battery backup, 3 phase or quad.
|
Boxed: 25"L x 23"W x 14"D
Weight: 40 Lbs.
|
|
|
$
1350.00
|
6000 Watt Autoformer for single inverter AC Coupled systems. Currently going through ETL testing.
|
|
|
|
$
219.00
|
SMA short back plate for inverter and E-Panel.
|
Size: 50.42"L x 22.88"W x 1.5"D
Weight: 26 Lbs.
|
|
|
$
269.00
|
SMA tall back plate for AC coupled Master. Holds inverter, E-Panel and Autoformer MNX-240.
|
Size: 65.44"L x 22.88"W x 1.5"D
Weight: 29 Lbs.
|
|
|
|
Relay Board that fits into the SMA Epanel to allow you to select between Generator and utility input. Essentially giving the Sunny Island 2 AC inputs. The SMARB auto senses the generator input and switches automatically. At the same time it gives the Sunny Island the required Digitial input wen the generator is running. The SMARB will not fit in the single AC coupled Epanel.
|
|
|
E-PANEL - XANTREX XW, DR/TR/SAMLEX
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
1150.00
|
E-Panel for a single Xantrex XW inverter/charger.
The XW inverter is mounted directly above the E-Panel for a 16 in wide assembly. Save $600 over the price of the Xantrex distribution panel and get additional features.
Left hand Charge control bracket: $20.00 weight: 1 Lb.
Listed by ETL for US & Canada
|
Size: 17" L x 16" W x 8.5" D
Boxed: 21" L x 21" W x 13" D
Weight: 38 lbs, Shipping Weight: 40.5 Lbs.
|
|
|
|
$
1350.00
|
Master E-Panel for a Dual Xantrex XW inverter/charger.
The XW inverter is mounted directly above the Requires a Slave Epanel for the second XW inverter
Left hand Charge control bracket: $20.00 weight: 1 Lb.
Listed by ETL for US & Canada
|
Size: 17" L x 16" W x 8.5" D
Boxed: 21" L x 21" W x 13" D
Weight: 38 lbs, Shipping Weight: 40.5 Lbs.
|
|
|
|
$
1005.00
|
E-Panel for a single Xantrex XW inverter/charger.
The XW inverter is mounted directly above the E-Panel for a 16 in wide assembly.
Left hand Charge control bracket: $20.00 weight: 1 Lb.
Listed by ETL for US & Canada
|
Size: 17" L x 16" W x 8.5" D
Boxed: 21" L x 21" W x 13" D
Weight: 38 lbs, Shipping Weight: 40.5 Lbs.
|
|
|
$
539.00
|
Works with all DR, TR and full length Samlex S series. Left hand unit only.
Listed by ETL for US & Canada
|
Size: 25" L x 11" W x 4" D
Boxed: 28" L x 14" W x 12" D
Weight: 28 Lbs.
|
|
|
|
$
579.00
|
Works with all DR, TR and full length Samlex S series. Left hand unit only.
Listed by ETL for US & Canada
|
Size: 25" L x 11" W x 4" D
Boxed: 28" L x 14" W x 12" D
Weight: 30 Lbs.
|
|
|
|
$
579.00
|
Works with all DR, TR and full length Samlex S series. Left hand unit only.
Listed by ETL for US & Canada
|
Size: 25" L x 11" W x 4" D
Boxed: 28" L x 14" W x 12" D
Weight: 30 Lbs.
|
|
E-PANEL - ULTRALITE - USE WITH NOTTAGUTTER
E-Panel - UltraLite Notes: UltraLite E-Panels are designed to go with the Nottagutter system. The UltraLites are a stripped down version of our stand alone E-Panels. The narrow 9.5" Outback variety comes in steel or aluminum. Magnum 120 VAC UltraLites come in steel and aluminum. Magnum 120/240 VAC comes in steel only. Each UltraLite comes with a 50 amp AC input disconnect, 125, 175 or 250 amp inverter breaker, ground busbar and the normal hardware and DC covers normally associated with E-Panels. They do not include an AC Bypass switch or AC and DC busbars.
E-Panel - UltraLite Notes: UltraLite E-Panels are designed to go with the Nottagutter system. The UltraLites are a stripped down version of our stand alone E-Panels. The narrow 9.5" Outback variety comes in steel or aluminum. Magnum 120 VAC UltraLites come in steel and aluminum. Magnum 120/240 VAC comes in steel only. Each UltraLite comes with a 50 amp AC input disconnect, 125, 175 or 250 amp inverter breaker, ground busbar and the normal hardware and DC covers normally associated with E-Panels. They do not include an AC Bypass switch or AC and DC busbars.
|
|
$
479.00
|
125 A/120 VAC narrow OutBack aluminum Left hand UltraLite E-Panel.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 19 Lbs.
|
|
|
|
$
519.00
|
175 A/120 VAC narrow OutBack aluminum Left hand UltraLite E-Panel. Listed by ETL for US & Canada.
|
Size: 37.5"L x 14"W x 3.5"D
Boxed: 28"L x 14"W x 12"D
Weight: 20 Lbs.
|
|
|
|
$
519.00
|
250 A/120 VAC narrow OutBack aluminum Left hand UltraLite E-Panel. Listed by ETL for US & Canada
|
Size: 37.5"L x 14"W x 3.5"D
Boxed: 28"L x 14"W x 12"D
Weight: 20 Lbs.
|
|
|
|
$
439.00
|
125 A/120 VAC narrow OutBack steel Left hand UltraLite E-Panel. Listed by ETL for US & Canada.
|
Size: 37.5"L x 14"W x 3.5"D
Boxed: 28"L x 14"W x 12"D
Weight: 28 Lbs.
|
|
|
|
$
479.00
|
175 A/120 VAC narrow OutBack steel Left hand UltraLite E-Panel. Listed by ETL for US & Canada
|
Size: 37.5"L x 14"W x 3.5"D
Boxed: 28"L x 14"W x 12"D
Weight: 29 Lbs.
|
|
|
|
$
479.00
|
250 A/120 VAC narrow OutBack steel Left hand UltraLite E-Panel. Listed by ETL for US & Canada.
|
Size: 37.5"L x 14"W x 3.5"D
Boxed: 28"L x 14"W x 12"D
Weight: 29 Lbs.
|
|
|
$
549.00
|
175 A/120 VAC wide Magnum steel Left hand UltraLite E-Panel. Listed by ETL for US & Canada
|
Size: 37.5"L x 14"W x 3.5"D
Weight: 39 Lbs.
|
|
|
|
$
549.00
|
250 A/120 VAC wide Magnum steel Left hand UltraLite E-Panel. Listed by ETL for US & Canada
|
Size: 37.5"L x 14"W x 3.5"D
Weight: 39 Lbs.
|
|
|
|
$
649.00
|
175 A/120/240 VAC wide Magnum steel Left hand UltraLite E-Panel. Listed by ETL for US & Canada
|
Size: 37.5"L x 14"W x 3.5"D
Weight: 42 Lbs.
|
|
|
|
$
649.00
|
250 A/120/240 VAC wide Magnum steel Left hand UltraLite E-Panel. Listed by ETL for US & Canada.
|
Size: 37.5"L x 14"W x 3.5"D
Weight: 42 Lbs.
|
|
|
|
$
649.00
|
NOTE: This product is being discontinued with limited quantities left.
175 A/120/240 VAC wide Apollo steel Left hand UltraLite E-Panel. Listed by ETL for US & Canada.
|
Size: 37.5"L x 14"W x 3.5"D
Weight: 42 Lbs.
|
|
|
|
$
649.00
|
NOTE: This product is being discontinued with limited quantities left.
250 A/120/240 VAC wide Apollo steel Left hand UltraLite E-Panel. Listed by ETL for US & Canada.
|
Size: 37.5"L x 14"W x 3.5"D
Weight: 42 Lbs.
|
|
E-PANEL LITE - FOR USE WITH SW, DR, RS ETC.
(Same size as OutBack narrow)
NOTE: All Lite’s come with a LH door, inverter breaker, pre-wired AC input and bypass, 500 amp/50mV shunt,
AC terminal blocks, din rails, wall mounting brackets, instructions and lots of hardware. Custom Lite
E- Panels can be built in the stretched enclosure in 120V and 120/240. Call for pricing.
ETL listed for the US and Canada
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
479.00
|
Gray steel with 125A/125VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 22 Lbs.
|
|
|
|
$
519.00
|
Gray steel with 175A/125VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 22 Lbs.
|
|
|
|
$
519.00
|
Gray steel with 250A/125VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 22 Lbs.
|
|
|
|
$
519.00
|
White Aluminum with 125A/125VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 15 Lbs.
|
|
|
|
$
559.00
|
White Aluminum with 175A/125VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 15 Lbs.
|
|
|
|
$
559.00
|
White Aluminum with 250A/125VDC inverter breaker.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 15 Lbs.
|
|
|
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
MNFUSE01-600V, MNFUSE02-600V, MNFUSE04-600V, MNFUSE06-600V, MNFUSE07-600V, MNFUSE08-600V, MNFUSE10-600V, MNFUSE12-600V, MNFUSE15-600V, MNFUSE20-600V, MNFUSE30-600V
|
$
3.75
|
Available in boxes of 10
Goes with MNTS fuse holder. The fuses are, Ferraz Shawmut/Mersen brand, industry standard 10mm x 38mm fuses.
NRTL listed to UL2579.
|
Weight: 0.2 Lbs.
|
|
|
|
$
4.75
|
Available in boxes of 10
Goes with MNTS fuse holder. The fuses are, Ferraz Shawmut/Mersen brand, industry standard 10mm x 38mm fuses.
NRTL listed to UL2579.
|
Weight: 0.2 Lbs.
|
|
|
$
6.25
100+ $5.50
|
Available in boxes of 12
Touch Safe Fuse Holder for10x38 mm fuses 600VDC 30 amp Din rail mount Use in the MNPV combiners for high voltage string inverters.
NRTL listed to UL2579.
|
Weight: 0.5 Lbs.
|
|
INVERTER SYSTEMS, PRE WIRED - AC COUPLED
|
|
$
6,749.00
|
MidNite AC coupled system Magnum 120/240 AC inverter 4,000 watt / 24VDC Inverter MidNite D3R battery box Capable of 4,000 watts of grid tie input.
ETL list for the US and Canada.
|
Boxed: 49"L x 39"W x 21"D Truck Freight Only
Weight: 200 Lbs.
|
|
|
$
5,199.00
|
MidNite AC coupled system Magnum 120/240 AC inverter 4,000 watt / 24VDC Inverter Capable of 4,000 watts of grid tie input.
ETL list for the US and Canada.
|
Boxed: 34"L x 34"W x 29"D Truck Freight Only
Weight: 190 Lbs.
|
|
|
$
9,775.00
|
MidNite AC coupled system dual Magnum 120/240 AC inverters 8,000 watt / 24VDC Inverter Capable of 8,000 watts of grid tie input.
ETL list for the US and Canada.
|
Boxed: Truck Freight Only
Weight: 365 Lbs.
|
|
|
$
15,774.00
|
MidNite AC coupled system using 3 Magnum 120/240 AC inverters 12,000 watt / 24VDC Inverter Capable of 12,000 watts of grid tie input.
ETL list for the US and Canada.
|
Boxed: Truck Freight Only
Weight: 471 Lbs.
|
|
|
$
19,426.00
|
MidNite AC coupled system. Four Magnum 120/240 AC inverters 16,000 watt / 24VDC Inverter Capable of 16,000 watts of grid tie input.
ETL list for the US and Canada.
|
Boxed: Truck Freight Only
Weight: 535 Lbs.
|
|
|
$
8,844.00
|
Nema 3R outdoor enclosure. Powder coated aluminum.
Schneider XW6048 120/240 vac Inverter.
AC Coupled, Off Grid or Grid tied.
6000 watt 48 volt inverter.
Listed by ETL for US & Canada
|
|
|
|
$
7,813.00
|
Schneider XW6048 120/240 vac Inverter
AC coupled.
6000 watt 48 volt inverter.
Listed by ETL for US & Canada.
|
Boxed: 56" L x 28" W x 19" D
Weight: 285 Lbs.
|
|
|
$
14941.00
|
2 Schneider XW6048 120/240 vac Inverter’s.
AC coupled.
2 6000 watt 48 volt inverters.
Listed by ETL for US & Canada
|
Boxed: 2 crates each being 56" L x 28" W x 19" D
Weight: (2 crates 285lbs each) 570 Lbs.
|
|
|
$
10,819.00
|
SMA Sunny Island 6048 120vac Inverter.
MidNite Autoformer for 240vac.
AC coupled.
6000 watt 48 volt inverter.
Listed by ETL for US & Canada
|
|
|
|
$
17,831.63
|
Dual SMA Sunny Island 6048 120vac Inverter’s wired for 120/240vac.
AC coupled.
Dual 6000 watt 48 volt inverters.
Listed by ETL for US & Canada
|
Boxed: 2 crates each being 56" L x 28" W x 19" D
Weight: (2 crates 275lbs each) 550 Lbs.
|
|
|
$
26,519
|
Triple SMA Sunny Island 6048 120vac Inverter’s wired for 3 phase AC
AC coupled.
Triple 6000 watt 48 volt inverters.
Listed by ETL for US & Canada
|
Boxed: 3 crates each being 56" L x 28" W x 19" D
Weight: (3 crates 275lbs each) 825 Lbs.
|
|
|
$
34,869.00
|
Quad SMA Sunny Island 6048 120vac Inverter’s wired for 120/240vac.
AC coupled.
4 6000 watt 48 volt inverters.
Listed by ETL for US & Canada
|
Boxed: 4 crates each being 56" L x 28" W x 19" D
Weight: (4 crates 275lbs each) 1100 Lbs.
|
|
|
$
11,864.00
|
Outback Radian 8048 120/240 vac Inverter.
Outdoor rated enclosure, Powder coated aluminum.
AC coupled.
8000 watt 48 volt inverter.
Listed by ETL for US & Canada
|
|
|
|
$
10,564.00
|
Outback Radian 8048 120/240 vac Inverter.
AC coupled.
8000 watt 48 volt inverter.
Listed by ETL for US & Canada
|
|
|
|
$
21,800.00
|
Radian Dual Outback 8048 120/240 VAC Inverters.
AC coupled.
2 8000 watt 48 volt inverters.
Listed by ETL for US & Canada.
|
|
|
INVERTER SYSTEMS, PRE WIRED - GRID TIE WITH BATTERY BACKUP
|
|
$
5439.00
|
OutBack Plus 120VAC System.
Battery backup Grid-Tie.
3600 Watt/48VDC Inverter.
Listed by ETL for US & Canada.
|
Boxed: 34" L x 34" W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
|
$
5439.00
|
OutBack Plus 120VAC System.
Battery backup Grid-Tie.
3500 Watt/24VDC Inverter.
Listed by ETL for US & Canada
|
Boxed: 34" L x 34" W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
$
5415.00
|
OutBack 120VAC System.
Grid Tie.
3500 Watt/24VDC Inverter.
Listed by ETL for US & Canada.
|
Boxed: 34" L x 34" W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
|
$
5415.00
|
OutBack 120VAC System.
Grid Tie.
3600 Watt/48VDC Inverter.
Listed by ETL for US & Canada.
|
Boxed: 34" L x 34" W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
$
11,500.00
|
Outback Plus 120/240VAC System.
Battery backup Grid-Tie.
Dual 3500 watt/24VDC Inverters.
Listed by ETL for US & Canada.
|
Boxed: 48" L x 32" W x 27" D Truck Freight Only
Weight: 365 Lbs.
|
|
|
|
$
11,500.00
|
Outback Plus 120/240VAC System.
Battery backup Grid-Tie.
Dual 3600 watt/48VDC Inverters.
Listed by ETL for US & Canada.
|
Boxed: 48" L x 32" W x 27" D Truck Freight Only
Weight: 365 Lbs.
|
|
|
$
11233.00
|
This Outback Radian complete power system is suitable for grid tied battery back up systems as well as stand alone off grid power.
|
|
|
|
$
23,600.00
|
This OutBack Radian complete power system is suitable for grid tied battery back up systems as well as stand alone off grid power.
|
Boxed: Truck Freight Only
|
|
|
$
8972.00
|
Schneider XW6048 120/240 vac Inverter.
Off Grid or Grid tied.
6000 watt 48 volt inverter.
Classic 150.
Listed by ETL for US & Canada.
|
Boxed: 56" L x 28" W x 19" D
Weight: 300 Lbs.
|
|
|
$
17179.00
|
Dual Schneider XW6048 120/240 vac Inverters.
Off Grid or Grid tied.
Dual 6000 watt 48 volt inverters.
Dual Classic 150s.
Listed by ETL for US & Canada
|
Boxed: 2 crates each being 56" L x 28" W x 19" D
Weight: (2 crates 300lbs each) 600 Lbs.
|
|
|
$
9780.00
|
SMA Sunny Island 6048 120vac Inverter.
Grid tied or Off Grid.
Classic 150 charge controller
6000 watt 48 volt inverter.
Listed by ETL for US & Canada.
|
|
|
INVERTER SYSTEMS, PRE WIRED - OFF GRID
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
5049.00
|
Magnum 120VAC System.
Off Grid.
4000 Watt/24VDC Inverter.
Listed by ETL for US & Canada
|
Boxed: 34"L x 34"W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
$
5399.00
|
Magnum 120/240VAC System.
Off Grid.
4000 Watt/24VDC Inverter.
Listed by ETL for US & Canada.
|
Boxed: 34"L x 34"W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
|
$
5399.00
|
Magnum 120/240VAC System.
Off Grid.
4400 Watt/48VDC Inverter.
Listed by ETL for US & Canada.
|
Boxed: 34"L x 34"W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
|
$
5439.00
|
OutBack Plus 120VAC System
Battery backup Grid-Tie
3500 Watt/24VDC Inverter (Sealed inverter available see options)
Listed by ETL for US & Canada
|
Boxed: 34" L x 34" W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
|
$
5439.00
|
OutBack Plus 120VAC System.
Off Grid.
3600 Watt/48VDC Inverter (Sealed inverter available see options).
Listed by ETL for US & Canada.
|
Boxed: 34" L x 34" W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
|
$
5415.00
|
OutBack 120VAC System.
Off Grid.
3500 Watt/24VDC Inverter (Sealed inverter available see options).
Listed by ETL for US & Canada.
|
Boxed: 34" L x 34" W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
|
$
5415.00
|
OutBack 120VAC System.
Off Grid.
3600 Watt/48VDC Inverter (Sealed inverter available see options).
Listed by ETL for US & Canada.
|
Boxed: 34" L x 34" W x 29" D Truck Freight Only
Weight: 190 Lbs.
|
|
|
|
$
11500.00
|
Outback Plus 120/240VAC System.
Off Grid.
Dual 3500 watt/24VDC Inverters (Sealed inverters available see options).
Listed by ETL for US & Canada.
|
Boxed: 48" L x 32" W x 27" D Truck Freight Only
Weight: 365 Lbs.
|
|
|
|
$
11,500.00
|
Outback Plus 120/240VAC System.
Off Grid.
Dual 3600 watt/48VDC Inverters (Sealed inverters available see options).
Listed by ETL for US & Canada.
|
Boxed: 48" L x 32" W x 27" D Truck Freight Only
Weight: 365 Lbs.
|
|
|
|
$
11233.00
|
This Outback Radian complete power system is suitable for grid tied battery back up systems as well as stand alone off grid power.
|
|
|
|
|
$
23,600
|
This Outback Radian complete power system is suitable for grid tied battery back up systems as well as stand alone off grid power.
|
Boxed: 34"L x 34"W x 29" D Truck Freight Only
|
|
|
$
3405.00
|
Magnum 120 VAC System.
Off Grid.
1500 Watt/ 24 VDC Inverter.
Classic 150 charge Controller.
Listed by ETL for US & Canada.
|
Boxed: 34"L x 34"W x 29" D Truck Freight Only
|
|
|
|
$
8972.00
|
Schneider XW6048 120/240 vac Inverter.
Off Grid or Grid tied.
6000 watt 48 volt inverter.
Classic 150.
Listed by ETL for US & Canada.
|
Boxed: 56" L x 28" W x 19" D
Weight: 300 Lbs.
|
|
|
|
$
17179.00
|
Dual Schneider XW6048 120/240 vac Inverters.
Off Grid or Grid tied.
Dual 6000 watt 48 volt inverters.
Dual Classic 150s.
Listed by ETL for US & Canada.
|
Boxed: 2 crates each being 56" L x 28" W x 19" D
Weight: (2 crates 300lbs each) 600 Lbs.
|
|
|
|
$
9780.00
|
SMA Sunny Island 6048 120vac Inverter.
Grid tied or Off Grid.
6000 watt 48 volt inverter.
Listed by ETL for US & Canada.
|
Boxed: 56" L x 28" W x 19" D
Weight: 285 Lbs.
|
|
|
$
20,000.00
|
Dual SMA Sunny Island 6048 120vac Inverters wired for 120/240vac.
Grid tied or Off Grid.
Dual Classic 150 charge controllers
6000 watt 48 volt inverters.
Listed by ETL for US & Canada.
|
Boxed: 2 crates each being 56" L x 28" W x 19" D
Weight: (2 crates 285lbs each) 570 Lbs.
|
|
INVERTER ENCLOSURES - OUTDOOR
Outdoor rated Enclosures for common battery based inverters.
|
|
$
1,300.00
|
Nema 3R enclosure for the XW, Radian or SMA inverter and there companion E-Panel.
|
|
|
|
|
$
949.00
|
Rain tight aluminum battery enclosure with locking door and two shelves. MNBE-D holds 4 GVX3050T or 4 golf cart or 8 group 31 batteries and an Inverter. Use sealed batteries only Requires one of our Back up kits found by following the link below. Ships knocked down in two boxes.
Instructional Videos:
Battery Enclosure Assembly Video
|
Size: 41.5"L x 34"W x 15.5"D
Boxed: Box 1: 43 x 19 x 8"
Box 2: 43 x 19 x 9"
Weight: Box 1 - 30 Lb/s
Box 2 - 52 Lbs.
|
|
|
|
$
1100.00
|
Battery Enclosure with locking door and one shelf. Outdoor 3R rain type design. Powder coated aluminum and stainless steel construction. Holds four 8D batteries. Has spaces for a 175 or 250 amp battery breaker as well as up to 4 MNDC panel mount breakers (1 to 100 amps available).
Breakers not included
Ships un-assembled.
|
Size: 36"L x 28.5"W x 26.25"D
|
|
|
Add -L to model for left hand breaker placement.
The MNDC comes with a din rail for 5 additional DC breakers for DC loads, charge controller
disconnect, battery status monitor feed etc. included is a ground bus, 5/16" bonding battery minus stud. Mounting holes for a 500 amp shunt are built in.
ETL listed for US and Canada
|
|
$
189.00
|
This is a MNDC with adapter attached for the smaller panel mount breakers (3/4 inch MNEDC panel mount breaker not included). Chassis is white powder coated aluminum with 5 dinrail breaker slots or 3 panel mount breaker slots.
Listed by ETL for US & Canada
|
Boxed: 10" X 5" X 18"
Weight: 6 Lbs.
|
|
|
$
299.00
|
General use enclosure for 15 panel mount type breakers from 5 - 100 Amp as well as a single 175 or 250 amp breaker if so desired.
NOTE: Busbars and breakers sold separately.
|
Size: 23"L x 12"W x 3.5"D
Boxed: 24"L x 13"W x 4"D
Weight: 25 Lbs.
|
|
|
$
220.00
|
White powder coated aluminum with 125A/125VDC breaker and 5 dinrail breaker slots or 3 panel mount breaker slots.
MNDC Drawings
Listed by ETL for US & Canada
|
Size: 17"L x 9"W x 4"D
Boxed: 18"L x 10"W x 5"D
Weight: 7 Lbs.
|
|
|
|
$
250.00
|
White powder coated aluminum chassis with 175A/125VDC breaker and 5 dinrail breaker slots or 3 panel mount breaker slots.
MNDC Drawings
Listed by ETL for US & Canada
|
Size: 17"L x 9"W x 4"D
Boxed: 18"L x 10"W x 5"D
Weight: 7 Lbs.
|
|
|
|
$
250.00
|
White powder coated aluminum chassis with 250A/125VDC breaker and 5 dinrail breaker slots or 3 panel mount breaker slots.
MNDC Drawings
Listed by ETL for US & Canada
|
Size: 17"L x 9"W x 4"D
Boxed: 18"L x 10"W x 5"D
Weight: 7 Lbs.
|
|
|
$
220.00
|
White powder coated aluminum with 125A/125VDC breaker and 5 dinrail breaker slots or 3 panel mount breaker slots. Left hand
MNDC Drawings
Listed by ETL for US & Canada
|
Size: 17"L x 9"W x 4"D
Boxed: 18"L x 10"W x 5"D
Weight: 7 Lbs.
|
|
|
|
$
250.00
|
White powder coated aluminum chassis with 175A/125VDC breaker and 5 dinrail breaker slots or 3 panel mount breaker slots.
MNDC Drawings
Listed by ETL for US & Canada
|
Size: 17"L x 9"W x 4"D
Boxed: 18"L x 10"W x 5"D
Weight: 7 Lbs.
|
|
|
|
$
250.00
|
White powder coated aluminum chassis with 250A/125VDC breaker and 5 dinrail breaker slots or 3 panel mount breaker slots.
MNDC Drawings
Listed by ETL for US & Canada
|
Size: 17"L x 9"W x 4"D
Boxed: 18"L x 10"W x 5"D
Weight: 7 Lbs.
|
|
|
$
265.00
|
MNDC Plus version of the popular MNDC
MNDCPLUS Drawing
Listed by ETL for US & Canada
|
Size: 17"L x 9"W x 4"D
Boxed: 18"L x 10"W x 5"D
Weight: 8 Lbs.
|
|
|
|
$
295.00
|
MNDC Plus version of the popular MNDC.
MNDCPLUS Drawing
Listed by ETL for US & Canada
|
Size: 17"L x 9"W x 4"D
Boxed: 18"L x 10"W x 5"D
Weight: 8 Lbs.
|
|
|
|
$
295.00
|
MNDC Plus version of the popular MNDC.
MNDCPLUS Drawing
Listed by ETL for US & Canada
|
Size: 17"L x 9"W x 4"D
Boxed: 18"L x 10"W x 5"D
Weight: 8 Lbs.
|
|
|
$
520.00
|
MNDC125-X2 utilizes the MidNite E-Panel enclosure. The door is blank. There are large 125A/125VDC battery breakers out each side for disconnecting two sources or loads.
Listed by ETL for US & Canada
|
Size: 25"L x 11"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 13 Lbs.
|
|
|
$
520.00
|
MNDC175-X2 utilizes the MidNite E-Panel enclosure. The door is blank. There are large 175A/125VDC battery breakers out each side for disconnecting two sources or loads.
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 29 Lbs.
|
|
|
|
$
520.00
|
MNDC250-X2 utilizes the MidNite E-Panel enclosure. The door is blank. There are large 250A/125VDC battery breakers out each side for disconnecting two sources or loads.
Listed by ETL for US & Canada
|
Size: 25"L x 16"W x 4"D
Boxed: 28"L x 14"W x 12"D
Weight: 29 Lbs.
|
|
|
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
699.00
|
Install up to four UltraLite E-Panels with each Nottagutter.
The Nottagutter accepts two E-Panels on top and two E-Panels bottom or on the sides
2 pole 60 amp bypass and 2 pole 60 amp Inverter breaker.
Supports 3 additional 2 pole 60 amp inverter breakers
Optional Din Rail bracket to support 6 additional Din Rail breakers
Locations for 2 panel mount breakers from 5 amp to 250 amp. See accessory’s below
Listed by ETL for US & Canada
|
Size: 37.5"L x 14"W x 3.5"D
Boxed: 40"L x 16"W x 6"D
Weight: 20 Lbs.
|
|
|
All of Midnite Solar’s listed balance of system products qualify for the US federal tax credit when used in a new, qualifying renewable energy system.
|
|
$
39.00
|
General use enclosure for retrofits, small inverter disconnect, PV disconnect, AC or DC distribution.
Used all around the world. 3/4 & 1" knockouts each end. Accepts up to 4 Din mount breakers from 1 to 63 Amps.
|
Size: 7"L x 3"W x 2.5"D
Boxed: 8"L x 4"W x 3"D
Weight: 2 Lbs.
|
|
|
$
48.00
|
General use enclosure - holds up to 4 13mm wide din rail breakers from 1-63 amps.
Listed by ETL for US & Canada
|
Size: 8"L x 5"W x 3"D
Boxed: 9"L x 6"W x 4"D
Weight: 3 Lbs.
|
|
|
$
58.00
|
General use aluminum enclosure for 4 panel mount type breakers from 5 - 100 Amp.
Not recommended for use with cables larger than awg #4 (19mm).
Listed by ETL for US & Canada
|
Size: 8"L x 5"W x 4"D
Boxed: 9"L x 6"W x 5"D
Weight: 4 Lbs.
|
|
|
|
$
299.00
|
General use enclosure for 15 panel mount type breakers from 5 - 100 Amp as well as a single 175 or 250 amp breaker if so desired.
NOTE: Busbars and breakers sold separately.
|
Size: 23"L x 12"W x 3.5"D
Boxed: 24"L x 13"W x 4"D
Weight: 25 Lbs.
|
|
|
The SPD is offered in three different voltages to maximize the required protection level. Protection is achieved by reducing the clamping voltage to a safe level that your system can sustain without damaging any electronics in the system. The MNSPD is designed to clamp a 115,000 amp surge! Blue LED’s provide visual indication of operation from a distance.
|
|
$
119.00
|
Purchase in quantity of 12 per box.
The MidNite Solar 115V Surge Protector Device (MNSPD) is a Type 1 device per UL1449 rev3. Protection for battery circuits. Listed by ETL for US & Canada.
SPD E-Panel Installation Video
SPD Comparison Test Video
SPD Install - Hawaii Video
Listed by ETL for US & Canada
|
Size: 4.4"L x 3.8"W x 3.5"D
Boxed: Case: 17"L x 13"W x 5.5"D
Ind box: 5"L x 4"W x 4"D
Weight: Case: 10 Lbs.
Ind: 1 Lbs.
|
|
|
|
$
119.00
|
Purchase in quantity of 12 per box.
The MidNite Solar 300V Surge Protector Device (MNSPD) is a Type 1 device per UL1449 rev3. Protection for Classic and other charge controllers, off grid PV combiners and 120/240 VAC circuits. Listed by ETL for US & Canada.
SPD Installation Video
SPD Comparison Test Video
SPD Install - Hawaii Video
Listed by ETL for US & Canada
|
Size: 4.4"L x 3.8"W x 3.5"D
Boxed: Case: 17"L x 13"W x 5.5"D
Ind box: 5"L x 4"W x 4"D
Weight: Case: 10 Lbs.
Ind: 1 Lbs.
|
|
|
|
$
119.00
|
Purchase in quantity of 12 per box.
The MidNite Solar 600V Surge Protector Device (MNSPD) is a Type 1 device per UL1449 rev3. Protection for grid-tie PV combiners and inverter input circuits. Listed by ETL for US & Canada.
SPD Installation Video
SPD Comparison Test Video
SPD Install - Hawaii Video
Listed by ETL for US & Canada
|
Size: 4.4"L x 3.8"W x 3.5"D
Boxed: Case: 17"L x 13"W x 5.5"D
Ind box: 5"L x 4"W x 4"D
Weight: 10 Lbs.
Ind 1 Lbs.
|
|
|
$
189.00
|
Our popular SPD 300 Surge Arrestor along with our new Flush mount box.
SPD Installation Video
SPD Comparison Test Video
Watch the Flush Mount Installation video
Listed by ETL for US & Canada
|
Size: 8.5"L x 6.5"W x 4"D
Boxed: 16.5L x 12.5W x 8.5D
Weight: 7 Lbs.
|
|
|
$
75.00
|
Purchase in quantity of 4 per box.
Flush mounting kit for MidNite Solar SPDs.
Watch the Flush Mount Installation video
|
Size: 8.5"L x 6.5"W x 4"D
Boxed: 16.5"L x 12.5"W x 8.5"D
Weight: 6 Lbs.
|
|
|
$
75.00
|
A non-functional counter top SPD (lightning arrestor) display.
|
Size: 8.5"L x 6.5"W x 4"D
Boxed: 16.5L x 12.5W x 8.5D
Weight: 7 Lbs.
|
|
|
|
|
$
139.00
|
Wiring Diagram 2
Dual 30 amp 240VAC Transfer Switch in the Big Baby. 6AWG max. Comes with neutral busbar and ground box terminal.
Listed by ETL for US & Canada
|
Size: 8"L x 5"W x 3.5"D
Boxed: 9"L x 6"W x 4"D
Weight: 4 Lbs.
|
|
|
|
$
139.00
|
Wiring Diagram 2
Dual 60 amp 240VAC Transfer Switch in the Big Baby. 6AWG max. Comes with neutral busbar and ground box terminal.
Listed by ETL for US & Canada
|
Size: 8"L x 5"W x 3.5"D
Boxed: 9"L x 6"W x 4"D
Weight: 4 Lbs.
|
|
WIND AND HYDRO ACCESSORIES
MidNite Classic and Classic Lite MPPT charge controllers work with Wind and Hydro.
|
|
$
1250.00
|
1,500 watt AC Clipper for wind or Hydro designed to work with the MidNite Classic. The Clipper comes in different resistance values per phase to allow you to tailor it to your specific turbine.
Clipper Installation video at Rick’s
Clipper Installation video at Tim’s
|
Size: 25.5"L x 15.5"W x 5.25"D
Boxed: 28"L x 18"W x 11"D
Weight: 50 Lbs.
|
|
|
|
$
1500.00
|
4,000 watt AC Clipper for wind or Hydro designed to work with the MidNite Classic. The Clipper comes in different resistance values per phase to allow you to tailor it to your specific turbine.
Clipper Installation video at Rick’s
Clipper Installation video at Tim’s
|
Size: 25.5"L x 15.5"W x 5.25"D
Boxed: 28"L x 18"W x 11"D
Weight: 50 Lbs.
|
|
|
|
$
1450.00
|
1,500 watt DC Clipper for Wind or Hydro designed to work with the MidNite Classic. The Clipper comes in different resistance values per phase to allow you to tailor it to your specific turbine.
Clipper Installation video at Rick’s
Clipper Installation video at Tim’s
|
Size: Size: 25.5"L x 15.5"W x 5.25"D
Boxed: Boxed: 28"L x 18"W x 11"D
Weight: 50 Lbs.
|
|
|
|
$
1700.00
|
4,000 watt DC Clipper for wind or Hydro designed to work with the MidNite Classic. The Clipper comes in different resistance values to allow you to tailor it to your specific turbine.
Clipper Installation video at Rick’s
Clipper Installation video at Tim’s
|
Size: 25.5"L x 15.5"W x 5.25"D
Boxed: 28"L x 18"W x 11"D
Weight: 50 Lbs.
|
|
|
$
470.00
|
The MidNite Turbine control box contains over current protection, a 3 Phase stop switch and a quality rectifier. The MNTCB contains two 277 VAC 60 Amp 3 phase AC breakers and a 1200 volt 200 Amp 3 phase bridge rectifier.
|
Boxed: 22"L x 18"W x 4.5"D
Weight: 11 Lbs.
|
|
|
$
99.00
|
Stop Switch for wind turbines 63 amp 150 VDC.
Listed by ETL for US & Canada.
|
Boxed: 9"L x 5"W x 4"D
Weight: 3 Lbs.
|
|
|
