Product Categories

Accessories
Backup System Kits
Battery Accessories
Battery Enclosures
Breakers
Busbars
Charge Controllers - Brat
Charge Controllers - Classics
Charge Controllers - KID
Combiners
Combiners - AC Micro Inverter (Example - Enphase)
Combiners - Disconnecting
Combiners - Pre-Wired
E-Panel - Magnum PAE 120/240VAC
E-Panel - Magnum
E-Panel - Outback
E-Panel - Samlex
E-Panel - Schneider Conext SW
E-Panel - Schneider Electric XW
E-Panel - SMA
E-Panel - UltraLite - Use with Nottagutter
E-Panel Lite - For use with TraceSW, DR, RS etc.
Fuses/ Fuse Holders
Inverter Systems, Pre Wired - AC Coupled
Inverter Systems, Pre Wired - Grid Tie with Battery Backup
Inverter Systems, Pre Wired - Off Grid
Inverter Systems, Pre Wired - UPS (Backup Power)
Mini DC Disconnect
Nottagutter
RAPID-SHUTDOWN-SYSTEM-NEC-690.12
Small Breaker Boxes
Software
Surge Protection Devices
Transfer switches
Wind and Hydro Accessories
Wind Products

Wind and Hydro Accessories

Back to Wind and Hydro Accessories
Printer Friendly Version
Download High Resolution Image
MNCLIP4KDCX.X
Model
Price Size Shipping Weight
MNCLIP4KDCX.X
$1700.00 25.5"L x 15.5"W x 5.25"D 28"L x 18"W x 11"D 50 Lbs
Generally speaking if your turbine has larger than a 10 foot rotor diameter and or is rated for 2.5KW or more you may need more than one clipper. Please consult tech support

The MidNite Clipper is designed to control Wind or Hydro turbines and work with the Classic to charge your battery. The Clipper communicates with the Classic to slow the turbine when the batteries are full, and also contains a stand alone self powered adjustable max VOC limiting circuit. The DC Clipper is designed to work with DC turbines and was designed for 3-4kw maximum turbines. The DC Clipper comes standard with 3.0 ohms of resistance per phase. We can custom build other resistance values upon request and have designed an easy to change resistor insert for the Clipper allowing changes in the field.

The 4,000 watt DC Clipper comes in several different resistance values. The standard values available are 3.0, 4.8 and 12ohms. Please add the value to the part number (For Example MNCLIP4KDC4.8) Please contact Customer service for help picking the correct resistance or if you need a value not listed.

AVAILABLE IN THE FOLLOWING MODEL NUMBERS:
  • MNCLIP4KDC3.0
  • MNCLIP4KDC4.8
  • MNCLIP4KDC12.0
Environmental Rating - Type 1 (Indoor)

Turbine Matrix for the Clipper

Clipper Installation video at Rick's
Clipper Installation video at Tim's

Warranty - 5 yrs.
Made in the USA
Description: 4,000 watt DC Clipper for wind or Hydro designed to work with the MidNite Classic. The Clipper comes in different resistance values to allow you to tailor it to your specific turbine.

Generally speaking if your turbine has larger than a 10 foot rotor diameter and or is rated for 2.5KW or more you may need more than one clipper. Please consult tech support


Please call Tech Support to verify your particular needs before ordering a Clipper from the Turbine Matrix as each system is different.

Recommended Accessories


CLASSIC 150 - $850.00
The Classic 150 MPPT Charge Controller - Listed by ETL for US & Canada CE Certified FCC Class B


CLASSIC 200 - $850.00
The Classic 200 MPPT Charge Controller - Listed by ETL for US & Canada CE Certified FCC Class B


CLASSIC 250 - $1050.00
The Classic 250 MPPT Charge Controller - Listed by ETL for US & Canada CE Certified FCC Class B


MNSPD-300-DC - $119.00
The MidNite Solar 300V Surge Protector Device (MNSPD) is a Type 2 device per UL1449 rev3 and has an outdoor rating of 4X for outdoor use. Protection for Classic and other charge controllers, off grid PV combiners and 120/240 VAC circuits.


MNEDC 5A thru 100A
5, 10, 15, 20, 30, 40, 50, 60, 70, 80, 90, 100 amp 150VDC Panel Mount. 10,000 AIC


MNCCCK - $7.50
Nipple Kit - One inch close nipple, three one inch lock nuts and two insulating bushings.


MNCCB-L or MNCCB-R - $20.00
CHARGE CONTROL BRACKETS - Right/Left - Right or left hand charge control brackets. Fits OutBack, Xantrex and MidNite MPPT controllers.

Product Search