|
|
FACTORY PRE-WIRED SYSTEMS
|
|
$4925.00
|
Magnum 120VAC System
Off Grid
4000 Watt/24VDC Inverter |
Boxed: 34 x 34 x 29"
Weight: 190 Lb/s.
|
|
|
$5299.00
|
Magnum 120/240VAC System
Off Grid
4000 Watt/24VDC Inverter |
Boxed: 34 x 34 x 29"
Weight: 190 Lb/s.
|
|
|
|
$5299.00
|
Magnum 120/240VAC System
Off Grid
4400 Watt/48VDC Inverter |
Boxed: 34 x 34 x 29"
Weight: 190 Lb/s.
|
|
|
$4999.00
|
OutBack Plus 120VAC System
Battery backup Grid-Tie
3500 Watt/24VDC Inverter |
Boxed: 34 x 34 x 29"
Weight: 190 Lb/s.
|
|
|
|
$4999.00
|
OutBack Plus 120VAC System
Battery backup Grid-Tie
3600 Watt/48VDC Inverter |
Boxed: 34 x 34 x 29"
Weight: 190 Lb/s.
|
|
|
|
$4999.00
|
OutBack Plus 120VAC System
Off Grid
3500 Watt/24VDC Inverter |
Boxed: 34 x 34 x 29"
Weight: 190 Lb/s.
|
|
|
|
$4999.00
|
OutBack Plus 120VAC System
Off Grid
3600 Watt/48VDC Inverter |
Boxed: 34 x 34 x 29"
Weight: 190 Lb/s.
|
|
|
$4975.00
|
OutBack 120VAC System
Grid Tie
3500 Watt/24VDC Inverter |
Boxed: 34 X 34 X 29"
Weight: 190 Lb/s.
|
|
|
|
$4975.00
|
OutBack 120VAC System
Grid Tie
3600 Watt/48VDC Inverter |
Boxed: 34 X 34 X 29"
Weight: 190 Lb/s.
|
|
|
|
$4975.00
|
OutBack 120VAC System
Off Grid
3500 Watt/24VDC Inverter
|
Boxed: 34 X 34 X 29"
Weight: 190 Lb/s.
|
|
|
|
$4975.00
|
OutBack 120VAC System
Off Grid
3600 Watt/48VDC Inverter |
Boxed: 34 X 34 X 29"
Weight: 190 Lb/s.
|
|
|
Note: For E-Panels built as Right hand units, add a -R to the end of the model number instead of the L. Right Hand versions have the hinge on the right, circuit breakers on the right and charge control bracket on the left.
Note: The Stretched version (STS) utilizes the 14.5 wide chassis to provide 5 additional wiring room.
Note: All E-Panels now come with a side plate that accommodates up to three panel mount breakers like the MNEDC80 or two panel mount breakers and DC-GFP80. These side plates also accommodate the OB Flexnet battery status monitor on 14.5 chassis versions. All OB E-Panels come with a Mate mounting bracket, PV+ busbar and 100 amp bat + busbar.
Note: The narrow Outback E-panels do not accommodate the OB surge arrester.
Note: All Outback E-Panels work with FX, VFX, GFX, and GVFX inverters.
Note: Add suffix (-E) for export versions wired with blue and brown wire. 277 VAC breakers are already standard on all E-Panels.
|
|
$489.00
|
Gray steel with 125a/125 VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 28 Lb/s.
|
|
|
|
$529.00
|
Gray steel with 175a/125 VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 29 Lb/s.
|
|
|
|
$529.00
|
Gray steel with 250a/125 VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 29 Lb/s.
|
|
|
$599.00
|
Stretched aluminum OB with FM60/80/Classic mounting on the door |
Weight: 24 Lb/s.
|
|
|
|
$639.00
|
Streched aluminum OB with FM60/80/Classic mounting on the door |
Weight: 27 Lb/s.
|
|
|
|
$639.00
|
Stretched aluminum OB with FM/60/80/Classic mounting on the door |
Weight: 27 Lb/s.
|
|
|
$529.00
|
White Alum with 125a/125VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 19 Lb/s.
|
|
|
|
$559.00
|
White Alum with 175a/125VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 23 Lb/s.
|
|
|
|
$559.00
|
White Alum with 250a/125VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 23 Lb/s.
|
|
|
$559.00
|
Stretched Gray steel with 125a/125VDC breaker |
Boxed: 18 X 11 X 28
Weight: 38 Lb/s.
|
|
|
|
$599.00
|
Stretched Gray steel with 175a/125VDC breaker |
Boxed: 18 X 11 X 28
Weight: 39 Lb/s.
|
|
|
|
$599.00
|
Stretched Gray steel with 250a/125VDC breaker |
Boxed: 18 X 11 X 28
Weight: 39 Lb/s.
|
|
|
$75.00
|
Gray Steel RH door with LH Chrg Cntrl Brkt for narrow OB chassis |
Boxed: 10 x 30 x 1"
Weight: 6 Lb/s.
|
|
|
$75.00
|
Wht Alum RH door with LH Chrg Cntrl Brkt for narrow OB chassis |
Boxed: 10 x 30 x 1"
Weight: 4 Lb/s.
|
|
|
$80.00
|
Gray steel RH door with LH Chrg Cntrl Brkt for wide OB chassis. |
Boxed: 15 x 30 x 1"
Weight: 8 Lb/s.
|
|
|
$20.00
|
|
Boxed: 12 x 8 x 7"
Weight: 2 Lb/s.
|
|
E-PANEL LITE - FOR USE WITH SW, DR, RS ETC. (SAME SIZE AS OUTBACK NARROW) NOTE: All Lites come with a LH door, inverter breaker, pre-wired AC input and bypass, 500 amp/50mV shunt,
AC terminal blocks, din rails, wall mounting brackets, instructions and lots of hardware. Custom Lite
E- Panels can be built in the stretched enclosure in 120V and 120/240. Call for pricing.
ETL listed for the US and Canada
|
|
$459.00
|
Gray steel with 125a/125VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 22 Lb/s.
|
|
|
|
$499.00
|
Gray steel with 175a/125VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 22 Lb/s.
|
|
|
|
$499.00
|
Gray steel with 250a/125VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 22 Lb/s.
|
|
|
|
$499.00
|
White Alum with 125a/125VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 15 Lb/s.
|
|
|
|
$539.00
|
White Alum with 175a/125VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 15 Lb/s.
|
|
|
|
$539.00
|
White Alum with 250a/125VDC inverter breaker |
Boxed: 14 X 12 X 28
Weight: 15 Lb/s.
|
|
|
|
$559.00
|
All included AC bypass and input disconnect breakers are rated for 277 VAC. Export versions
of our standard E-Panels are made using Blue and Brown wire and terminal bus bar insulators.
Add an E to the end of any model number to create an E-Panel suited for Africa, Australia,
New Zealand or Europe. Prices are the same as regular E-Panels.
Example: MNE125ST-R-E (Shown) Refer to the North American versions for size, weight and price. |
Boxed: 11 x 14 x 28
|
|
|
The Magnum E-Panel comes with inverter breaker, 2/0 inverter cables, pre-wired AC input and bypass, 500amp 50mV shunt, AC terminal blocks, 100 amp DC positive and DC negative bus bars, PV input bus bar, din rails, 3 panel mount breaker knockouts, Ground bus bar, DC wiring cover, top shield, remote display mounting bracket, wall mounting brackets, charge controller bracket and lots of hardware and grommets.
ETL listed for the US and Canada
|
|
$599.00
|
Gray steel with 175a/125VDC inverter breaker for RD1824, RD2824, RD2624E and MS2712E
Here is a stacked pair wiring diagram: Wiring Diagram 2
Evolution of the E-Panel |
Boxed: 18 X 11 X 28
Weight: 39 Lb/s.
|
|
|
|
$599.00
|
Gray steel with 250a breaker for MS4024/ MS2812/MS2012/MS4124E & RD series.
Here is a stacked pair wiring diagram: Wiring Diagram 2
Evolution of the E-Panel |
Boxed: 18 X 11 X 28
Weight: 39 Lb/s.
|
|
|
$529.00
|
Designed for the Magnum Energy MM series inverters. |
|
|
|
|
$639.00
|
White aluminum with 175a breaker for MS4024/MS2812/MS2012/MS4124E & RD series.
Evolution of the E-Panel |
Boxed: 18 x 11 x 28
Weight: 31 Lb/s.
|
|
|
|
$639.00
|
White aluminum with 250a breaker for MS4024/MS2812/MS2012/MS4124E & RD series.
Evolution of the E-Panel |
Boxed: 18 x 11 x 28
Weight: 31 Lb/s.
|
|
|
$75.00
|
Gray steel right hand hinge door with LH charge control braket for wide chassis |
Boxed: 15 x 30 x 1"
Weight: 8 Lb/s.
|
|
MAGNUM AE E-PANEL - 120/240VAC The AE series comes with all the regular E-Panel features plus terminal bus bars for 120/240VAC input and
output.
NOTE: 120 VAC E-Panels cannot be adapted for use with 120/240 inverters.
ETL listed for the US and
Canada
|
|
$799.00
|
White steel for 120/240VAC in & out for MS4448-AE |
Boxed: 18 x 11 x 28
Weight: 42 Lb/s.
|
|
|
|
$799.00
|
White steel for 120/240VAC in & out for MS4024-AE |
Boxed: 18 x 11 x 28
Weight: 42 Lb/s.
|
|
XANTREX XW, DR/TR/SAMLEX E-PANELS
|
|
$519.00
|
Works with all DR, TR and full length Samlex S series |
Boxed: 11 x 14 x 28
Weight: 28 Lb/s.
|
|
|
|
$559.00
|
Works with all DR, TR and full length Samlex S series |
Weight: 30 Lb/s.
|
|
|
|
$559.00
|
Works with all DR, TR and full length Samlex S series |
Boxed: 11 x 14 x 28
Weight: 30 Lb/s.
|
|
|
$950.00
|
E-Panel for a single Xantrex XW inverter/charger
The XW inverter is mounted directly above the E-Panel for a 16 assembly. Save $600 over the price of the Xantrex distribution panel and get additional features.
Left hand Charge control bracket: $20.00 weight: 1 Lb. |
Boxed: 16 x 18 x 8
Weight: 42 Lb/s.
|
|
|
|
$799.00
|
Works with all Apollo inverters |
Boxed: 18 x 11 x 28"
Weight: 42 Lb/s.
|
|
|
|
$799.00
|
Works with all Apollo inverters |
Boxed: 18 x 11 x 28"
Weight: 42 Lb/s.
|
|
|
Add Left to model for left hand breaker placement.
The MNDC comes with a din rail for 5 additional DC breakers for DC loads, charge controller
disconnect, battery status monitor feed etc. included is a ground bus, 5/16bonding battery
minus stud. Mounting holes for a 500 amp shunt are built in.
ETL listed for US and Canada
|
|
$205.00
|
White alum with 125a/125VDC breaker and 5 dinrail breaker slots or 3 panelmount breaker slots. |
Boxed: 10 X 5 X 18
Weight: 7 Lb/s.
|
|
|
|
$235.00
|
White alum chassis with 175a/125VDC breaker and 5 dinrail breaker slots or 3 panelmount breaker slots. |
Boxed: 10 X 5 X 18
Weight: 7 Lb/s.
|
|
|
|
$235.00
|
White alum chassis with 250a/125VDC breaker and 5 dinrail breaker slots or 3 panelmount breaker slots. |
Boxed: 10 X 5 X 18
Weight: 7 Lb/s.
|
|
|
$205.00
|
White alum with 125a/125VDC breaker and 5 dinrail breaker slots or 3 panelmount breaker slots. Left hand |
Boxed: 10 X 5 X 18"
Weight: 7 Lb/s.
|
|
|
|
$235.00
|
White alum chassis with 175a/125VDC breaker and 5 dinrail breaker slots or 3 panelmount breaker slots. |
Boxed: 10 X 5 X 18
Weight: 7 Lb/s.
|
|
|
|
$235.00
|
White alum chassis with 250a/125VDC breaker and 5 dinrail breaker slots or 3 panelmount breaker slots. |
Boxed: 10 X 5 X 18
Weight: 7 Lb/s.
|
|
|
$250.00
|
MNDC Plus version of the popular MNDC |
|
|
|
|
$280.00
|
MNDC Plus version of the popular MNDC |
|
|
|
|
$280.00
|
MNDC Plus version of the popular MNDC |
|
|
|
Note: All combiner enclosures will accept Delta style lightning arresters.
Note: See www.midnitesolar.com/documents/dimensiondrawings/ for enclosure size and locations.
Note: All enclosures can accept bulkhead mount MC connectors for faster on roof time.
Note: Call for pricing on factory installed MC/Tyco bulkhead connectors
|
|
$89.00
|
(For 150 VDC charge controllers and 600 VDC gridtie inverters)
Gray aluminum type 3R rainproof enclosure with deadfront, will accept three 150VDC (MNEPV)
breakers or two 600 VDC fuse holders. |
Boxed: 11 x 5 x 4"
Weight: 2 Lb/s.
|
|
|
$109.00
|
(For 150 VDC charge controllers and 600 VDC gridtie inverters)
(The most popular PV combiner in North America.) Gray aluminum type 3R rainproof enclosure with insulating dead front, will accept six 150VDC breakers or 4 600VDC fuse holders. |
Boxed: 9 x 14 x 4"
Weight: 4 Lb/s.
|
|
|
$179.00
|
(For 150 VDC charge controllers and 600 VDC gridtie inverters) Gray aluminum type 3R rainproof enclosure with insulating dead front, will accept 12 150VDC breakers or 10 600VDC fuse holders. |
Boxed: 16 x 14 x 5"
Weight: 8 Lb/s.
|
|
|
$189.00
|
(For 200/300 VDC charge controllers)
Gray aluminum type 3R rainproof enclosure with insulating dead front, will accept 6 300VDC breakers. |
Boxed: 16 x 14 x 5
Weight: 8 Lb/s.
|
|
|
$399.00
|
For up to 100,000 watt 600 VDC gridtie inverters.
|
Boxed: 16 x 14 x 5 "
Weight: 13 Lb/s.
|
|
|
$399.00
|
The MNPV16-24 PV combiner can hold up to 24 single pole 150VDC breakers. |
Boxed: 22 x 18 x 5"
Weight: 13 Lb/s.
|
|
|
$399.00
|
For use with 300VDC breakers for high powered, high voltage off-grid applications. |
Boxed: 22 x 18 x 5"
Weight: 13 Lb/s.
|
|
|
|
$45.00
|
General use enclosure - holds up to 4 13mm wide dinrail breakers from 1-63 amps. |
Boxed: 9 x 5 x 4"
Weight: 3 Lb/s.
|
|
|
$36.00
|
General use enclosure for retrofits, small inverter disconnect, PV disconnect, AC or DC distribution or?
Used all around the world. Ύ & 1 knockouts each end. |
Boxed: 3 x 3 x 7"
Weight: 2 Lb/s.
|
|
|
$55.00
|
An enclosure that holds 4 MNEDC80 type breakers. Midnite stocks 60, 70, 80, 90, & 100 amp. |
Boxed: 9 x 5 x 4"
Weight: 4 Lb/s.
|
|
|
$129.00
|
Wiring Diagram 2
Dual 30 amp 240VAC Transfer Switch in the Big Baby. Non-listed. 6AWG max. Comes with neutral busbar and ground box terminal. |
Boxed: 9 x 5 x 4"
Weight: 4 Lb/s.
|
|
|
|
$129.00
|
Wiring Diagram 2
Dual 60 amp 240VAC Transfer Switch in the Big Baby. Non-listed. 6AWG max. Comes with neutral busbar and ground box terminal |
Boxed: 9 x 5 x 4"
Weight: 4 Lb/s.
|
|
|
$89.00
|
Disconnects turbine from batteries and shorts out turbine.
Comes with neutral busbar and ground box terminal.
|
Boxed: 9 x 5 x 4"
Weight: 3 Lb/s.
|
|
|
|
$699.00
|
Install up to four UltraLite E-Panels with each Nottagutter.
The Nottagutter accepts two E-Panels on top and two E-Panels bottom or on the sides as shown to the right. |
Boxed: 40 x 16 x 6
Weight: 20 Lb/s.
|
|
|
|
$699.00
|
Dual 60 amp bypass and 250 amp single breakers. |
Boxed: 40 x 16 x 6
Weight: 20 Lb/s.
|
|
|
|
$729.00
|
Dual 60 amp and four 50 amp single breakers. |
Boxed: 40 x 16 x 6
Weight: 20 Lb/s.
|
|
|
|
$759.00
|
Dual 60 amp bypass and six 50 amp single breakers. |
Boxed: 40 x 16 x 6
Weight: 20 Lb/s.
|
|
|
|
$789.00
|
Dual 60 amp bypass and eight 50 amp breakers. |
Boxed: 40 x 16 x 6
Weight: 20 Lb/s.
|
|
|
$479.00
|
125 A/120 VAC narrow OutBack aluminum Left hand UltraLite E-Panel
|
Boxed: 14 x 12 x 28"
Weight: 19 Lb/s.
|
|
|
|
$519.00
|
175 A/120 VAC narrow OutBack aluminum Left hand UltraLite E-Panel |
Boxed: 14 x 12 x 28"
Weight: 20 Lb/s.
|
|
|
|
$519.00
|
250 A/120 VAC narrow OutBack aluminum Left hand UltraLite E-Panel
|
Boxed: 14 x 12 x 28"
Weight: 20 Lb/s.
|
|
|
$439.00
|
125 A/120 VAC narrow OutBack steel Left hand UltraLite E-Panel
|
Boxed: 14 x 12 x 28"
Weight: 28 Lb/s.
|
|
|
|
$479.00
|
175 A/120 VAC narrow OutBack steel Left hand UltraLite E-Panel
|
Boxed: 14 x 12 x 28"
Weight: 29 Lb/s.
|
|
|
|
$479.00
|
250 A/120 VAC narrow OutBack steel Left hand UltraLite E-Panel
|
Boxed: 14 x 12 x 28"
Weight: 29 Lb/s.
|
|
|
$549.00
|
175 A/120 VAC wide Magnum steel Left hand UltraLite E-Panel
|
Boxed: 18 x 11 x 28"
Weight: 39 Lb/s.
|
|
|
|
$549.00
|
250 A/120 VAC wide Magnum steel Left hand UltraLite E-Panel
|
Boxed: 18 x 11 x 28"
Weight: 39 Lb/s.
|
|
|
$649.00
|
175 A/120/240 VAC wide Magnum steel Left hand UltraLite E-Panel
|
Boxed: 18 x 11 x 28"
Weight: 42 Lb/s.
|
|
|
|
$649.00
|
250 A/120/240 VAC wide Magnum steel Left hand UltraLite E-Panel |
Boxed: 18 x 11 x 28"
Weight: 42 Lb/s.
|
|
|
$649.00
|
175 A/120/240 VAC wide Apollo steel Left hand UltraLite E-Panel
|
Boxed: 18 x 11 x 28"
Weight: 42 Lb/s.
|
|
|
|
$649.00
|
250 A/120/240 VAC wide Apollo steel Left hand UltraLite E-Panel |
Boxed: 18 x 11 x 28"
Weight: 42 Lb/s.
|
|
|
|
$425.00
|
Battery Enclosure with locking door. Holds three group 31 or 27 sealed batteries per shelf side by side
or two per shelf end to end. Also holds one 8D per shelf.. Two cabinets can be stacked horizontal or vertical for
expansion. Remove middle shelf for taller batteries. 2 knock outs on top and sides. Gray powder coated steel. Ships
knocked down.
Enclosure outside dimensions: 29 wide x 14.5 deep x 27.25 tall
|
Boxed: 30 x 32 x 7.5
Weight: 71 Lb/s.
|
|
|
$605.00
|
Battery Enclosure with locking door. Holds eight group 31 or sealed golf cart sized batteries. Gray
powder coated steel. Two cabinets can be stacked horizontal or vertical for expansion. Ships knocked down in two
cartons.
Enclosure size: 33.6 wide x 15.25 deep x 34.2 tall
Boxed size & weight: Box 1 of 2 Doors and Back 18 x 8 x 36 40 Lbs.
Box 2 of 2 Sides, Top and Shelves. |
Boxed: Box 1: 49 x 19 x 8
Box 2: 50 x 19 x 9"
Weight: Box 1: 41 Lb/s
Box 2: 66 Lb/s.
|
|
|
$849.00
|
MNBE-C Battery Enclosure with locking door. Holds twelve group 31 or sealed golf cart sized batteries and even
the 14 tall PVX-3050T from Concorde. Gray powder coated steel. Two cabinets can be stacked horizontal for expansion.
Enclosure size: 36.5 wide x 16 deep x 55 tall/190 Lbs including pallet (freight truck only)
NOTE: There is an additional $100 crating fee on top of product price. |
Weight: 190 Lb/s.
|
|
|
$649.00
|
(Our best value) Battery Enclosure with locking door. With two shelves the MNBE-D holds 8 GVX3050 or 8 golf cart or 8 group 31 batteries. With the optional third shelf, the MNBE-D holds 12 group 31 batteries. The image shows 8 GVX3050 batteries. Ships knocked down in two boxes. |
Boxed: Box 1: 49 x 19 x 8"
Box 2: 50 x 19 x 9"
Weight: Box 1 - 45 Lb/s
Box 2 - 68 Lb/s.
|
|
|
$749.00
|
Battery Enclosure with locking door. Holds eight L16 batteries on two shelves. Holds 12 group 31 or golf cart batteries with additional shelf. Gray powder coated steel. Two cabinets can be stacked horizontal for expansion. Use the Large back up kits to have 2 shelves of batteries plus inverter & charge controller on the top 3rd shelf. Ships knocked down in two cartons. |
Boxed: Box 1: 49 x 19 x 8"
Box 2: 50 x 19 x 9"
Weight: Box 1: 54 Lb/s
Box 2: 74 Lb/s.
|
|
|
$949.00
|
An aluminum outdoor enclosure which is identical to the MNBE-D |
|
|
|
$89.00
|
Extra shelf for MNBE-C, MNBE-D, or MNBE-D3K |
|
|
|
|
$69.00
|
63 amp 150VDC DC ground fault protector (UL listed breaker assy).
NEC2008 requires DC-GFPs on all solar installations. |
Weight: 2 Lb/s.
|
|
|
$69.00
|
80 amp 125VDC DC ground fault protector (UL listed breaker assy)
½ amp trip mechanism connects between battery negative and earth ground
NEC2008 requires DC-GFPs on all solar installations. |
Weight: 2 Lb/s.
|
|
|
$119.00
|
50 amp 300VDC ground fault protector (UL listed breaker assembly). |
Boxed: 9 x 5 x 4"
Weight: 2 Lb/s.
|
|
|
$15.00
|
10, 15, & 20 amp 120VAC UL489A din rail mount. |
Boxed: 13mm wide
Weight: 1 Lb/s.
|
|
|
$15.00
|
30-60 amp 120VAC UL1077 din rail mount |
Boxed: 13mm wide
Weight: 1 Lb/s.
|
|
|
$15.00
|
White 15 amp 277VAC UL1077 single pole. |
|
|
|
|
$15.00
|
White 30 amp 277VAC UL1077 single pole. |
|
|
|
|
$15.00
|
White 50 amp 277VAC UL1077 single pole. |
|
|
|
$30.00
|
White 30 amp 277VAC UL1077 double pole |
|
|
|
|
$30.00
|
White 50 amp 277VAC UL1077 double pole. |
|
|
|
|
$30.00
|
White 60 amp 277VAC UL1077 double pole |
|
|
|
$54.00
|
White or black 30 amp 277VAC UL1077 triple pole. |
Boxed: 1.5 wide
|
|
|
|
$54.00
|
White or black 50 amp 277VAC UL1077 triple pole. |
|
|
|
$30.00
|
20 amp 120/240 VAC UL489 two pole |
Boxed: 26mm wide
Weight: 2 Lb/s.
|
|
|
|
$30.00
|
50 amp 120/240 VAC UL1077 two pole |
Boxed: 26mm wide
Weight: 2 Lb/s.
|
|
MNEDC05, 10, 15, 20, 30, 40, 50, 60, 70, 80, 90, 100
|
$20.00
|
05 through 100 amp 150VDC Panel Mount. |
Boxed: Ό " studs Ύ" wide
Weight: 1 Lb/s.
|
|
|
$54.00
|
125amp 125VDC Panel Mount |
Boxed: Ό studs 1" wide
Weight: 2 Lb/s.
|
|
|
$6.00
|
1 to Ύ Breaker Adapter |
Weight: Boxed: 2 L Lb/s.
|
|
|
$109.00
|
125VDC 3/8 studs 1.5 |
Weight: 3 Lb/s.
|
|
|
$13.00
|
150VDC din rail mount breaker
(13mm wide) 1 Lb. Part number example: MNEPV15
Always in stock: 1,2,3,4,5,6,7,8,9,10,12,15,20,30,40,50,63 amps
MNEPV breakers are the same as CBI QY breakers available elsewhere except ours are 150VDC!
150VDC ETL listed in the US and Canada
|
Boxed: 13mm wide
Weight: 1 Lb/s.
|
|
|
$34.00
|
7 through 50 amp 300VDC UL489 listed din rail mount breaker. |
Weight: 2 Lb/s.
|
|
|
|
$99.00
|
8 studs for multiple paralleled battery strings. |
Weight: 2 Lb/s.
|
|
|
$75.00
|
280 amps, Same busbar used in the Nottagutter. Five battery connections.
Comes with auxiliary terminal busbar for six small wires #14-1/0. |
Weight: 1 Lb/s.
|
|
|
$12.00
|
3.45 long with Green screws! Two 1/0 & seven #6 wire
slots. Comes with mounting screws. Made in USA, UL and CSA recognized. |
Weight: 1 Lb/s.
|
|
|
$13.00
|
This .093 thick copper bus has three fingers spaced at ½ (13mm) intervals
one box lug is provided to accommodate 14-1/0 AWG wire. |
Weight: 1 Lb/s.
|
|
|
$15.00
|
MNPV6 BUSBAR This .093 thick copper bus has six fingers spaced at ½ (13mm) intervals
Two box lugs are provided to accommodate 14-1/0 AWG wire. |
Weight: 1 Lb/s.
|
|
|
$13.00
|
This .063 thick copper bus has four fingers spaced at Ύ (19mm) intervals
One box lug is provided that accommodates 14-1/0 AWG wire. |
Weight: 1 Lb/s.
|
|
|
$10.00
|
2.3 long. Two 1/0 & four #6 wire slots. Comes with mounting screw& nut #10-32 x 7/8. Made in USA, UL and CSA recognized. |
Weight: 1 Lb/s.
|
|
|
$15.00
|
(Midnite Short Busbar) Shorter version of the insulated bus bars. These are useful for PV+ input on the narrow OB E-Panel and for a separate PV- bus bar for
charge controllers that require them. Four #6 and two 1/0 wire slots. |
Weight: 1 Lb/s.
|
|
|
$13.00
|
Without insulators. Comes with 10-32 screws.
Bus Bar 4.63 UL and CSA recognized, Made in USA. Insulators ETL recognized, Designed by MidNite Solar and Made in China 1Lb. Remove the plastic insulators for ground bus applications. A dimensioned drawing is on the MidNite website as Long MNTB Dimensions.
|
|
|
|
$17.00
|
Four 1/0 & eleven #6 useable wire slots. Comes with two lengths of 10-32 screws |
Weight: 1 Lb/s.
|
|
|
$49.00
|
Mounts on 500 shunt. Same busbar used in the Nottagutter. Four battery cable studs and six position aux terminal busbar.
Shunt sold separately. |
Weight: 1 Lb/s.
|
|
|
|
$359.00
|
This kit allows an installer or do-it yourselfer a chance to get into a
battery backed up power system at a very modest price. The kit includes
all of the following:
Battery breaker (175 or 250 amp), 50 amp AC bypass assembly, 50 amp
AC input breaker, two 15 amp load circuit breakers, Din rail support,
breaker cover plate, AC terminal blocks, hardware and instructions. Use
with MNBE-B or C battery enclosure purchased separately. |
|
|
BACKUP SYSTEM KITS - LARGE These kits provide all the necessary breakers and brackets to assemble your own Power
back up system. The /GEN versions have the extra
generator input transfer switch and AC inlet. Use these kits with our B or C
battery enclosures.
175 OR 250 amp breaker MUST SPECIFY BREAKER SIZE
AC ground bus bar
AC input and output terminal blocks for field wiring connections
GFCI outlet and associated 15 amp breaker wired
Two 15 amp and one 20 amp load circuit breakers
50 amp AC breakers (AC input disconnect and AC bypass switch)
500 amp/50mV shunt for connection of battery and inverter negatives with bat negative busbar
AC inlet for portable generator recessed on side for Large Backup Kit/gen models
50 amp utility/15 amp generator transfer switch on 120 VAC/gen models
50 amp utility/30 amp generator transfer switch on 240 VAC/gen models
Knockout spaces for four additional AC or DC breakers on non-gen models
Mounting hardware for Magnum or OutBack inverter
|
|
$750.00
|
New Product! |
|
|
|
|
$850.00
|
|
|
|
|
|
$800.00
|
New Product! |
|
|
|
|
$900.00
|
|
|
|
|
|
$69.00
|
Battery Capacity Meter |
Boxed: 5 x 4 x 2
Weight: .5 Lb/s.
|
|
|
$239.00
|
16 gauge gray steel accepts one or two EPanels,
(wide or narrow). Wires route
behind the 2 thick plate for a clean
installation. Rear cover plates enclose
wires from mounting surface. |
Boxed: 48 x 31 x 3
Weight: 25 Lb/s.
|
|
|
$7.50
|
One inch close nipple, three one inch lock nuts and two insulating bushings. Use for connecting charge controllers through the side to MidNite E-Panels or other simular enclosures. |
Weight: 1 Lb/s.
|
|
|
$12.00
|
063 x 2.1 x 1.5 One 3/8, five .250, two .203 holes. Used on MNDC shunts for an additional bat minus connections. |
Weight: 1 Lb/s.
|
|
|
$36.00
|
500amp/50mV includes taptite mounting screws. Has two 8-32 tapped holes on one end to attach a bus bar. This is the industry standard shunt. |
Weight: 2 Lb/s.
|
|
|
$40.00
|
Aluminum or steel |
Weight: 2 Lb/s.
|
|
|
$60.00
|
Gray steel, ships with two single pole sliders not shown. |
Weight: 2 Lb/s.
|
|
|
$65.00
|
White steel, ships with two pole sliders not shown |
Weight: 2 Lb/s.
|
|
|
$6.25
100+ $5.50
|
Touch Safe Fuse Holder for10x38 mm fuses 600VDC 30 amp Din rail mount
Use in the MNPV combiners for high voltage string inverters. |
Weight: 1 Lb/s.
|
|
|
$22.00
|
Double ganged 2 pole Touch safe fuse holder for 10 x 38mm fuses. This fuse holder is used for transformer less grid tie inverter arrays. One pole is plus VDC and the other is minus VDC. The MNPV combiners do not yet accommodate this fuse holder. |
Weight: 1 Lb/s.
|
|
|
$6.25
100+ $5.50
|
Goes with MNTS fuse holder. The fuses are the industry standard 10mm x 38mm fuses. |
Weight: 1 Lb/s.
|
|
|
|
100+ $3.95
|
Goes with MNTS fuse holder. The fuses are the industry standard 10mm x 38mm fuses.
Only sold in quantities of 100 |
Weight: 1 Lb/s.
|
|